Aqua-Scope Ball Valve Servo - Motor to operate ball valves

Technical characteristics

Home Automation Technology	Z-Wave 700 Series

More info

The BVS (Ball Valve Servo) with Z-Wave is a motor to retrofit existing and installed ball valves into smart water controlling devices. The motor is powered by a 12 V external power supply.

The variable clamps allow mounting even in complex pipe installations. The patented motor coupling ensures easy installation and precise long-term operation. The device can operate in difficult environmental conditions, even submerged under water and allows to directly connect one additional local water sensor pad by cable.

Remote control: Control your main water or gas valve remotely, when you have your Ball Valve Servo connected to a Z-Wave gateway.

Simple, Tools-Free: Just snap on and turn 2 knobs. Done in less then one minute!

Elbow proof: Can be installed on pipe elbows by adjustable clamps position.

Smart Adaptive Torque Control: Protects motor, valve and pipe for long term operation.

Outdoor Proof: IP67 rated, worked even submerged under water.

Integrated Water Detection Probe and Freeze Detection. Works Offline as well.

Features:

Power Supply. 12 V / 1 A external power supply (included)
Simple, Tools-Free: Just snap on and turn 2 knobs. Done in less then one minute!
Elbow proof: Can be installed on pipe elbows by adjustable clamps position
Smart Adaptive Torque Control: Protects motor, valve and pipe for long term operation
Outdoor Proof: IP67 rated, worked even submerged under water
Installation: Valves ½ inch to 1 ¼ inch
Integrated Water Detection Probe and Freeze Detection. Works Offline as well.
Clamp size: 64 - 124 mm adjustable
Max Driving Force: 6 Nm
Valve Control: Full open/Close, any position in between down to 1 % stepping
Protocol: Z-Wave 700-Series
Operatint temperature: - 30 °C - 80 °C

Article Dimensions (WxHxL)	145 x 130 x 60 mm
Package Dimensions (WxHxL)	236 x 179 x 114 mm
Article net weight	0.801 Kg
Article gross weight	1.147 Kg
Z-Wave Plus
Z-Wave S2
WEEE
CE
IP-Rating	IP67

Extended Z-Wave info

Name: Custos Ball Valve Servo

Manufacturer:Custos

Identifier:BVSZWE

Z-Wave Certification Number:ZC12-21020179

Hardware Plattform:ZGM130

FLiRS:NO

Role Type:Always On Slave

Short Description:Custos Ball Valve Servo (BVS) is the most advance retrofit valve controller for real DIY

Description:With patented mechanic design, Custos BVS can be installed by yourself on existing valve of your water main within 20 seconds without any tool, to provide fully automated shutoff against flooding. A super strong and advance mechanic combined with smart software algorithm allows the BVS to deal with even the toughest valve without compromising the integrity of your valve over the time. Key features: 1. Hassle free bare hand install in 20 seconds 2. Outdoor proof, can be deployed on water main outside your house 3. Build-in local leak detection probe, can work standalone 4. Elbow friendly, adjustable clamp span can fit in smallest space or oversized valve up to 1.25 inches 5. Smart adaptive torque control and self calibration, real plug and play without any hassle for adjustment or calibration.

Manual download HERE.

Group

Max Nodes

Description

1

5

Lifeline Group - Device Reset Locally Notification - Basic Report - Binary Switch Report - Indicator Report - Sensor Multilevel Report – Temperature “Auto report based on Configuration Parameter 0x22 Setting.” - Heat Alarm Notification Report (0x04) - 0x00 = State idle - 0x02 = Overheat – no location support - - 0x06 = Underheat – no location support - Water Alarm Notification Report (0x05) - 0x00 = State idle - 0x02 = Water leak detected – no location support - Water Valve Notification Report (0x0F) - 0x01 = Valve operation - 0x00 = VALVE CLOSED/OFF (Valve does not let the water run through.) - 0x01 = VALVE OPEN/ON (Valve lets the water run through)

2

5

- Basic Set (By default the Configuration CC parameter 0x11 (17) “Inverse Water Valve report” is enabled to send out following report.) - 0x00 = Let the water run through (Based on Configuration Parameter 0x13) - 0xFF = Doesn’t let the water run through. (Based on Configuration Parameter 0x12) - 0x00 = Let the water run through (Based on Configuration Parameter 0x13) - 0xFF = Doesn’t let the water run through. (Based on Configuration Parameter 0x12)

3

5

- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x32 Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x31 Setting)

4

5

- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x27 Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x26 Setting)

5

- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x2C Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x2B Setting)

Number

Size (Bytes)

Default Value

Name

Description

17

1

Inverse Water Valve Report

Inverses Switch Binary Report when Water Valve = 0x00 “Valve doesn’t let the water run through in Notification and real physical status.”

18

1

Association Group 2 SET Value

Configure Association Group 2 Basic Set value when Binary Switch Report = 0xFF *(Related to Configuration setting 0x11)

19

1

2

Association Group 2 SET Value

Configure Association Group 2 Basic Set value when Binary Switch Report = 0x00 *(Related to Configuration setting 0x11)

33

1

Temperature Report Unit

Configure Temperature Unit report. The default Unit is depended on Regional Frequency Setting. (By default, US=°F and EU=°C)

34

2

260

Temperature Threshold Change

Configure Temperature threshold changed and send auto report

35

2

256

Temperature Report Offset

Configure Temperature Offset degree; Higher byte 0x = Positive degree and 1x= Negative degree.

36

2

360

Overheat Trigger Value

Configure Overheat report trigger value. “Higher byte 0x00 represents Celsius °C unit, 0x01 represents Fahrenheit °F unit

37

2

342

Overheat Recover value

Configure Overheat Recover report value

38

1

0

Association Group 4 Overheat Trigger

Configure Overheat Trigger Value in Association Group 4

39

1

0

Association Group 4 Overheat Cancel

Configure Overheat Cancellation SET value

40

2

288

Freeze Trigger Value

Configure Freeze Trigger Report value

41

2

292

Freeze Recover Value

Configure Freeze Recover Report Value

42

1

Freeze Detection Valve Control

Enable / Disable Valve Control during Freeze when Water Leak is detected “Detected by built-in temperature sensor. Refer to Configuration CC parameter 0x28 (41) & 0x29 (42)

43

1

0

Association Group 5 Freeze Trigger

Configure Association Group 5 Freeze Detection Trigger Basic Set value

44

1

0

Association Group 5 Freeze Cancel

Configure Association Group 5 Freeze Detection Cancellation Basic Set value

49

1

Association Group 3 Water Leak Trigger

Configure Association Group 3 Water Leak Trigger Basic Set value

50

1

0

Association Group 3 Water Leak Cancel

Configure Association Group Water Leak Cancellation Basic Set value

51

1

Water Leak Detection Valve Control

Disable / Enable Valve Control when Water Leak detected

65

1

Buzzer

Enable / Disable Built-in Buzzer Sound

66

1

80

LED Brightness Level

Configure Built-in LED Brightness Level

67

1

0

Touch Keylock Protection

Disable / Enable Touch Keylock Protection

81

1

13

Notification Report

Configure Notification Report in Association Group 1 Lifeline “Set Bit to 0 = Disable, Set Bit to 1 = Enable” Default value 0x0D (13) Only available values as below xxxx xxx0 = Disable to report valve Open / Close status xxxx xxx1 = Enable to report valve Open / Close status (Default) xxxx xx0x = Disable Overheat Detection (Default) xxxx xx1x = Enable Overheat Detection xxxx x0xx = Disable Freeze (Underheat) Detection xxxx x1xx = Enable Freeze (Underheat) Detection (Default) xxxx 0xxx = Disable Water Leak Detection xxxx 1xxx = Enable Water Leak Detection (Default)

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Information V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V3

COMMAND_CLASS_ASSOCIATION_V3

Basic V2

COMMAND_CLASS_BASIC_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific

COMMAND_CLASS_MANUFACTURER_SPECIFIC

Multi-Channel Association V4

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V4

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Multilevel V11

COMMAND_CLASS_SENSOR_MULTILEVEL_V11

Supervision

COMMAND_CLASS_SUPERVISION

Switch Binary V2

COMMAND_CLASS_SWITCH_BINARY_V2

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset Procedure

Factory Default Reset:

To remove Custos BVS without involve gateway in Exclusion / Remove device operation and BVS will reset all setting to Factory Default

Setting.

i. Start: Long hold Touch Sense Button for 10 seconds then short click 5 times.

ii. Processing: Yellow LED ON 1 second then wait 2-5 seconds.

iii. Success: Green LED on 2 second with long beep sounds for 2 seconds.

*Factory Default Reset will:

a. Remote the BVS from Z-Wave Network;

b. Delete the association setting;

c. Restore the configuration settings to the default.

Classic Exclusion

Remove Custos BVS from Z-Wave Network:

Set your Z-Wave Gateway into Exclusion mode / Remove device.

i. Start: Short press Touch Sense Button 3 times.

ii. Processing: Yellow LED and short beep sound keeping continue.

iii. Success: Green LED on 1 second with 2 short beep sounds.

iv. The LED indication Changes to Yellow LED blinking.

Other Special Features

None

Where to find S2 DSK on product

The DSK is printed on the product itself and also packaging label can be found outside the giftbox

Classic Inclusion

Classic Inclusion:

Set your Z-Wave Gateway into Inclusion mode / Add device.

i. Start: Short press Touch Sense Button 3 times.

ii. Processing: Yellow LED and short beep sound keeping continue. For security inclusion support, you may need to entering first 5 digit

that show on QR Code label, please refer to the instructions of central controller.

iii. Success: Green LED on 1 second with 2 short beep sounds.

iv. The LED indication changes to Green LED slow blinking from Yellow LED blinking.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Outdoor Use

Product is suitable for use outdoors.

Switch Type

Describes the type of operator for a switch.