Philio PAN08 Roller Shutter Controller - Z-Wave Blind Driver

1

1

Lifeline There is only one group called Group1, there is only one node for Group1 which support MULTILEVEL_SWITCH_REPORT, METER_REPORT_COMMAND_V3, ALARM_REPORT.

1

2

720

Watt Meter Report Period

If the setting is configured for 1hour (set value =720), the Micromodule will report its instant power consumption every 1 hour to the node of corresponding Group. The maximum interval to report its instant power consumption is 45 hours (5s*32767/3600=45hr). Default value is 1 hour.

2

2

6

KWH Meter Report Period

If the setting is configured for 1hour (set value =6), the Micromodule will report its Accumulated Power Consumption (KW/h) every 1 hour to the node of corresponding Group. The maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55 days). Default value=1 hour.

3

2

500

Threshold of current for Load Caution

This is a warning when the wattage of load exceeds the preset threshold value, If the setting value is 500, when the load current over this value, Micromodule will send current meter report command to the node of corresponding Group. Default value=500.

4

2

10000

Threshold of KWH for Load Caution

This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power Consumption of Relay1 or Relay2 over this value, Micromodule will send KWh Meter Report command to the node of corresponding Group, minimum value is 1KWh and default value is 10000 kWh.

5

1

1

External switch type

1.ONE PUSH BUTTON When the configuration setting is One Push Button, only S1 input will be valid. The control moving commands can be accepted in this switch type while the shutter is moving. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 just like the operation of include button. When S1 is short pressed, the shutter will move up toward TOP(0xFF). If during this movement S1 is short pressed again, the shutter will stop moving. A third short pressing of S1 will move the shutter down toward BOTTOM(0x00). If during this movement S1 is short pressed again, the shutter will stop moving. And so on… Inverting direction and stopping. 2.TWO PUSH BUTTON: (THE DEFAULT SETTING IS TWO PUSH BUTTON (2)) If this setting is configured as Two Push Button, S1 and S2 input will be valid, but will not accept pressing S1 and S2 at the same time. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 or S2 just like the operation of include button. When S1 is pressed and held more than 1.5 seconds, the shutter will move up toward TOP(0xFF), and the shutter will stop moving when S1 is released. When S2 is pressed and held for more than 1.5 seconds, the shutter will move down toward BOTTOM(0x00), and the shutter will stop moving when S2 is released.When S1 is short pressed, the shutter will move up toward TOP(0xFF). If during this movement S1 i short pressed again S1 again, the shutter just keep moving up toward TOP(0xFF). The easy way to stop this moving is short pressing S2. When S2 is short pressed, the shutter will move down toward BOTTON(0x00). If during this movement S2 is short pressed again S2 again, the shutter just keep moving down toward BOTTON(0x00). The easy way to stop this moving is short pressing S1. When in Two Push Button switch type, S1 or S2 are pressed and not released, and PAN08 receive any control moving command from Z-Wave RF (Ex. BASIC_SET, BINARY_SWITCH_SET, MULTILEVEL_SWITCH_SET, MULTILEVEL_SWITCH_START_LEVEL_CHANGE or MULTILEVEL_SWITCH_STOP_LEVEL_CHANGE or SCENE_ACTIVATION_SET), PAN08 won’t do any change in position but report alarm to Group1 (Alarm_Type=1, Alarm_level =0xFF), this indicate that the S1 or S2 not been release.

6

1

2

Level report mode

Mode 1 : In 5 seconds period after controlled by a moving command, it will report the destination level when received request command. Out of the 5 seconds period, it will report the actual level of the shutter when received request command. Mode 2 : Whenever the shutter moves past a 10 percent level, it will auto report the level to Group 1 node.

Alarm

COMMAND_CLASS_ALARM

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V2

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Powerlevel

COMMAND_CLASS_POWERLEVEL

Scene Activation

COMMAND_CLASS_SCENE_ACTIVATION

Scene Actuator Conf

COMMAND_CLASS_SCENE_ACTUATOR_CONF

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset

Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

Pressing Include button three times within 2 seconds will enter inclusion mode.

Within 1 second, press Include button again for 5 seconds until LED is off.

IDs are excluded.

Inclusion

Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.

Pressing Include button three times within 2 seconds will enter inclusion mode.

Exclusion

Put the Z-Wave Controller in exclusion mode.

Pressing Include button three times within 2 seconds will enter exclusion mode.

Node ID has been excluded.

Electric Load Type

Select the electric load type(s) supported by the device.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Switch Load Capacity Watts

The amount of switch load energy the product is rated for in Watts

Loads Controlled

The number of different loads controllable by the product if it supports more than one.

Supported Meter Type

Indicate which type of metering is supported by the device.

Switch Type

Describes the type of operator for a switch.

Window Covering Control Features

Select the feature(s) supported in the Window Covering Control product.

Color

If the product is only available in one color, pick the color from the list.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.