Shelly Qubino Wave 2PM Micromodule Dual relay consumption measurement Z-Wave

Technical characteristics

Technology	Z-Wave Serie 800

More info

Z-Wave smart switch micromodule, 2 channels 16 A total current (18 A peak), with power measurement.

Remotely control two independent electrical appliances (e.g. lights) and monitor their energy consumption separately and in total.

2 channels (2x 10 A, 16 A total)
Power measurement on each channel and in total
Extremely low power consumption: 0.3 W.
Z-Wave frequency band: 868.4 MHz (CEPT countries)
Latest technology: Z-Wave 800 Series
Automatic configuration with SmartStart
Security 2 authenticated for the highest level of security
Supports firmware updates over the air
Easy installation into most standard electrical boxes and switches
Works with certified Z-Wave gateways and over 4,000 Z-Wave devices
*A gateway (smart hub) is not included. A gateway (smart hub) is required for device configuration.

Works with any Z-Wave gateway
Wave 2PM is retrofit and designed to fit behind any switch or socket, instantly transforming it into a smart one. Once installed, add it to your Z-Wave network (Z-Wave gateway required) and control connected appliances from anywhere using your smartphone or tablet. Shelly Qubino devices work with over 4,000 Z-Wave certified devices and gateways.

Works with Z-Wave

Connect Wave 2PM to your Z-Wave network and control it remotely. It is compatible with all certified Z-Wave gateways.

Associations

Establish direct communication between devices on your local Z-Wave network and define custom actions without the need for a hub.

Power monitoring

Wave 2PM provides accurate monitoring of power consumption on each channel separately and in total.

Wide voltage range

Use it to control a wide range of devices and appliances.

Smart schedules

Create custom schedules aligned with your daily routine or sync with sunrise/sunset to manage your lighting (gateway required).

Smart scenes

Set up custom scenes by combining Wave 2PM with any other Z-Wave device (gateway required).

Control two lights with a single device

Wave 2PM allows you to remotely control two lights or other electrical appliances and monitor their energy consumption. Use the manual switch, the Smart Home app, the home automation system or voice control. Easy, convenient and energy efficient!

Control your energy consumption and save money

With Wave 2PM you can accurately measure the power consumption of each channel separately (W) and together (W, kWh). Monitor real-time consumption of connected devices and adjust usage patterns to easily reduce utility costs.

Create schedules that follow your daily routine

Increase the energy efficiency of your home and simplify your daily life. Schedule your lights to come on gradually each morning at 7 or at dusk if the house is occupied. This way, your home can automatically follow your daily routine and create an environment that suits you at a certain time of day.

The Shelly Qubino Wave 2PM module is a Z-Wave 800 integrated switch with two outputs. The module supports active energy metering and is designed to control devices such as lights, fans, infrared panels, heaters and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as via a wall switch.

The module can be powered by a voltage of 110-240 VAC or 24 DC, allowing flexibility in power supply. The maximum load capacity in AC is 16 A and in DC is 10 A. The Wave 2PM outputs can switch 10A individually and 16A combined.

In addition, the module is equipped with various protection functions, such as overheating, overvoltage and overcurrent protection.

Characteristics

Z-Wave 800 Series
Maximum load capacity in AC: 16 A, in DC: 10 A
Protected against overheating
Supports over-the-air (OTA) firmware updates
Can be used with different types of switches

Specifications

power supply	110-240 V AC / 24 V DC +/-10%
Power consumption	<0.3W
Power measurement (W)	Forks
Max switching voltage AC	240V
Max switching current AC	10 A per channel, 16 A total, 18 A total peak
Max switching voltage DC	30V
Max switching current DC	10A
Overheating protection	Forks
Overload protection	Forks
Distance	Up to 40 m indoors (131 ft.) (depends on local condition)
Z-Wave repeater:	Forks
CPU	Z-Wave" S800
Z-Wave" frequency band:	868.4MHz
Maximum radio frequency power transmitted in frequency band(s)	<25mW
Size (H x W x D)	37x42x16 ±0.5 mm / 1.46x1.65x0.63 ±0.02 in
Mounting	wall console
Screw terminals max. torque	0.4 Nm / 3.5 lbin
Cross section driver	0.5 to 1.5 mm² / 20 to 16 AWG
Driver stripped length	5 to 6 mm / 0.20 to 0.24 in
shell material	Plastic
Color	Black
Ambient temperature	-20°C to 40°C / -5°F to 105°F
Humidity	30% to 70% RH
Max. altitude	2000 m / 6562 ft.

Extended Z-Wave info

Name: Wave 1PM

Manufacturer:Shelly Qubino

Identifier:QNSW-001P16EU

Z-Wave Certification Number:ZC14-23100356

Hardware Plattform:EFR32ZG23A

FLiRS:NO

Role Type:Always On End Node

Short Description:The Device is a single product that enables the control of the on/off function for one electrical device such as bulb, ceiling fan, IR heater. It measures the power consumption of the connected device.

Description:The Device is a single product that enables the control of the on/off function for one electrical device such as bulb, ceiling fan, IR heater. It measures the power consumption of the connected device.

Group

Max Nodes

Description

1

9

2

9

3

9

Number

Size (Bytes)

Default Value

Name

Description

1

2

SW1 Switch type

0 push, 1 toggle state, 2 toggle change

120

1

0

Factory reset

17

1

0

Restore state of O1 after power failure

0 restore, 1 no restore

19

2

0

Turn O1 OFF Automatically with timer

0 - 32535, 0 disabled

20

2

0

Turn O1 ON Automatically with timer

0 - 32535, 0 disabled

201

4

2147483647

Serial Number 1

202

4

2147483647

Serial Number 2

203

4

2147483647

Serial Number 3

23

1

0

O1 NO/NC

0 NO, 1 NC

25

1

0

Set timer units to Seconds or Milliseconds for O1

0 seconds, 1 millisecods

36

1

50

O1 Power report on change - percenatge

1-100 percentage, 0 disabled

39

1

30

O1 min reporting time

1-120 seconds, 0 disabled

91

4

0

Alarm conf. - Water

0 no action 1 open relay 2 close relay

92

4

0

Alarm conf. - Smoke

0 no action 1 open relay 2 close relay

93

4

0

Alarm conf. - CO

0 no action 1 open relay 2 close relay

94

4

0

Alarm conf. - Heat

0 no action 1 open relay 2 close relay

Association Group Information (AGI) V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Binary Switch V2

COMMAND_CLASS_SWITCH_BINARY_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V6

COMMAND_CLASS_METER_V6

Multi Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security 0

COMMAND_CLASS_SECURITY

Security 2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

When adding the Device to a Z-Wave network with a gateway supporting Security 2 (S2), the PIN Code of the Z-Wave Device Specific Key (DSK) is required. You can find it on the label on the side of the Device and a copy is inserted in the packaging, which must not be lost. Do not remove the Z-Wave DSK label from the Device. As a backup measure, use the label in the packaging.

The first five digits of the key are highlighted or underlined to help the user identify the PIN Code part of the DSK text. The DSK is additionally represented with a QR Code as shown on the image.

Classic Inclusion

6.1 Adding the Device to a Z-Wave™ network (inclusion)

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.

6.1.1 SmartStart adding (inclusion)

SmartStart enabled products can be added into a Z-Wave™ network by scanning the Z-Wave™ QR Code present on the Device with a gateway providing SmartStart inclusion. No further action is required, and the SmartStart device will be added automatically within 10 minutes of being switched on in the network vicinity.

1. With the gateway application scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list in the gateway.

2. Connect the Device to a power supply.

3. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

4. Adding will be initiated automatically within a few seconds after connecting the Device to a power supply, and the Device will be added to a Z-Wave™ network automatically.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

6.1.2 Adding (inclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2, etc.) 3 times within 3 seconds (this procedure puts the Device in Learn mode*). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

*Learn mode - a state that allows the Device to receive network information from the gateway.

6.1.3 Adding (inclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the adding process.

7. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Classic Exclusion

Removing the Device from a Z-Wave™ network (exclusion)

Note! The Device will be removed from your Z-wave™ network, but any custom configuration parameters will not be erased.

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.

6.2.1 Removing (exclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the removing process.

6. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.

6.2.2 Removing (exclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the removing process.

7. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Factory Reset Procedure

6.3 Factory reset

6.3.1 Factory reset general

After Factory reset, all custom parameters and stored values (kWh, associations, routings, etc.) will return to their default state. HOME ID and NODE ID assigned to the Device will be deleted. Use this reset procedure only when the gateway is missing or otherwise inoperable.

6.3.2 Factory reset with a switch/push-button

Note! Factory reset with a switch/push-button is only possible within the first minute after the Device is connected to a power supply.

1. Connect the Device to a power supply.

2. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 5 times within 3 seconds. The Device must receive on/off signal 5 times, which means pressing the push-button 5 times, or toggling the switch on and off 5 times.

3. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s.

4. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.3 Factory reset with the S button

Note! Factory reset with the S button is possible anytime.

1. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

2. Press the S button multiple times until the LED turns solid red.

3. Press and hold (> 2s) S button on the Device until the red LED starts blinking in Mode 3. Releasing the S button will start the factory reset.

4. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s.

5. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.4 Remote factory reset with parameter with the gateway

Factory reset can be done remotely with the settings in Parameter No. 120.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Color

If the product is only available in one color, pick the color from the list.

Electric Load Type

Select the electric load type(s) supported by the device.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.