Shelly Qubino Wave 1 - Dry Contact Micromodule Simple Relay up to 16A

Technical characteristics

Home Automation Technology	Z-Wave Serie 800

More info

Z-Wave relay in Dry Contact micromodule format (potential free)

Extremely low power consumption: 0.3 W.
Latest technology: Z-Wave 800 Series Chip
Z-Wave frequency band: 868.4 MHz (CEPT countries)
Automatic configuration with SmartStart
Security 2 authenticated for the highest level of security
Supports over-the-air (OTA) firmware updates
Works with certified Z-Wave gateways and over 4,000 Z-Wave devices
*A home automation controller (smart hub) is not included. A Z-Wave gateway (smart hub) is required for device configuration.

The Shelly Qubino Wave 1 module is a Z-Wave 800 embedded switch with a potential-free output. The module is designed to control devices such as electric locks, garage doors, entry doors, irrigation systems, power outlets and lighting. With a maximum load capacity of 16A, the module provides enough power for various applications. It is possible to control the module wirelessly via Z-Wave, as well as via a wall switch.

The module can be powered with a voltage of 110-240 V AC, 24-48 V DC or 12 V DC, providing flexibility in power supply. Additionally, the output is potential-free, meaning that the input voltage can differ from the device you want to switch. This allows compatibility with various electrical devices. Additionally, the module is equipped with overheating protection.

Shelly Qubino is powered by Z-Wave
By using Z-Wave, smart home products can seamlessly communicate with each other, regardless of their brand or platform, thanks to a centralized smart hub! Shelly Qubino devices are powered by the latest generation of Z-Wave chips (S800), one of the most popular standardized smart home technologies in the world.

*Z-Wave devices have specific requirements to function properly, such as the need to use a compatible Z-Wave hub.
For more information, please visit the official Z-wave website: www.z-wave.com.

Works with any Z-Wave home automation controller

Wave 1 is retrofit and designed to fit behind any switch or socket, instantly transforming it into a smart one. Once installed, add it to your Z-Wave network (Z-Wave gateway required) and control connected appliances from anywhere using your smartphone or tablet. Shelly Qubino devices work with over 4,000 Z-Wave certified devices and gateways.

Characteristics

Works with Z-Wave technology

Connect Wave 1 to your Z-Wave network and control it remotely. It is compatible with all certified Z-Wave gateways.

Associations

Establish direct communication between devices on your local Z-Wave network and configure custom actions without the need for a hub.

dry contact

Connect different power loads (up to 16 A) to the device, which has an internal potential-free relay (dry contact) electrically isolated from the micromodule's own power supply.

Wide voltage range

Uses a wide range of output voltage levels. Supports low voltages.

Custom schedules

Create custom schedules aligned with your daily routine or sync with sunrise/sunset to manage your lighting (gateway required).

Smart scenes

Set up custom scenes by combining Wave 1 with any other Z-Wave device (gateway required)...

Endless applications of use

Automate your garden irrigation system effortlessly

Keeping your garden green with a busy lifestyle can be a challenge, but with an automated irrigation system, you can effortlessly manage your garden's watering needs with a tap on your smartphone, even when you're on vacation. For complete peace of mind, simply schedule your watering and the sprinklers will automatically turn on and off. Yes, that easy.

Control your garage door remotely

Have you closed the garage door when leaving home? From now on, you just have to check it on your smartphone. Wave 1 has operating voltages of 12V DC and 24-48V DC, making it perfect for garage door control.

Set up partnerships and let your home welcome you

Configure Wave 1 and other devices on your Z-Wave network and create associations between them for direct communication without a gateway. Automate the door lock and lights and set a rule: every time the front door is unlocked, the lobby/hallway lights come on.

Automate your lights and make them follow your schedule

Make any light switch smart with Shelly Wave 1 and control them through your phone or with a voice assistant. Use your hub app to set up automated scenes based on a time or sunset/sunrise. This way, you can schedule your porch lights to come on around the time you get home from work, or your hallway lights to turn off after your family's bedtime. And don't worry: the light switches can still be used manually to suit the needs of everyone in your home.

TECHNICAL SPECIFICATIONS

Feeding	110-240 V AC / 24-48 V DC / 12 V DC ± 10%
Consumption at rest	<0.3W
Max Voltage of the relay in AC	240V
Max current of the relay in AC	16A
Max Voltage of the relay in DC	30V
Max current of the relay in DC	10A
Protection against overheating	Yeah
Distance	Up to 40 m indoors (131 ft.) (depends on local conditions)
"Z-Wave" repeater:	YEAH
Chip	Z-Wave" S800
Z-Wave Frequencies":	868.4MHz; 865.2MHz; 869.0MHz; 921.4MHz; 908.4MHz; 916MHz; 919.8MHz; 922.5MHz; 919.7-921.7-923.7MHz; 868.1MHz; 920.9MHz
Maximum radio frequency power transmitted in the frequency band(s)	<25mW
Size (H x W x D)	37x42x16 ±0.5 mm / 1.46x1.65x0.63 ±0.02 in
Weight	26g/0.92oz.
Mounting	Mechanism box or register box
Max tightening torque screw terminals	0.4 Nm / 3.5 lbin
Driver section	0.5 to 1.5 mm² / 20 to 16 AWG
Conductor Stripped Length	5 to 6 mm / 0.20 to 0.24 in
Housing material	Plastic
Color	Blue
Room temperature	-20°C to 40°C / -5°F to 105°F
Humidity	30% to 70% RH
Max. altitude	2000 m / 6562 ft.

Extended Z-Wave info

Name: Wave 1

Manufacturer:Shelly Qubino

Identifier:QNSW-001X16EU

Z-Wave Certification Number:ZC14-23090326

Hardware Plattform:EFR32ZG23A

FLiRS:NO

Role Type:Always On End Node

Short Description:Wave 1 controls the on/off function for one electrical device, e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. The output contact is potential-free (dry contact).

Description:Wave 1 controls the on/off function for one electrical device, e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. The output contact is potential-free (dry contact).

Group

Max Nodes

Description

1

9

2

9

3

9

Number

Size (Bytes)

Default Value

Name

Description

1

2

SW1 Switch type

0 push, 1 toggle state, 2 toggle change

120

1

0

Factory reset

17

1

0

Restore state of O1 after power failure

0 restore, 1 no restore

19

2

0

Turn O1 OFF Automatically with timer

0 - 32535, 0 disabled

20

2

0

Turn O1 ON Automatically with timer

0 - 32535, 0 disabled

201

4

2147483647

Serial Number 1

202

4

2147483647

Serial Number 2

203

4

2147483647

Serial Number 3

23

1

0

O1 NO/NC

0 NO, 1 NC

25

1

0

Set timer units to Seconds or Milliseconds for O1

0 seconds, 1 millisecods

91

4

0

Alarm conf. - Water

0 no action 1 open relay 2 close relay

92

4

0

Alarm conf. - Smoke

0 no action 1 open relay 2 close relay

93

4

0

Alarm conf. - CO

0 no action 1 open relay 2 close relay

94

4

0

Alarm conf. - Heat

0 no action 1 open relay 2 close relay

Association Group Information (AGI) V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Binary Switch V2

COMMAND_CLASS_SWITCH_BINARY_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security 0

COMMAND_CLASS_SECURITY

Security 2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

When adding the Device to a Z-Wave network with a gateway supporting Security 2 (S2), the PIN Code of the Z-Wave Device Specific Key (DSK) is required. You can find it on the label on the side of the Device and a copy is inserted in the packaging, which must not be lost. Do not remove the Z-Wave DSK label from the Device. As a backup measure, use the label in the packaging.

The first five digits of the key are highlighted or underlined to help the user identify the PIN Code part of the DSK text. The DSK is additionally represented with a QR Code as shown on the image.

Classic Inclusion

6.1 Adding the Device to a Z-Wave™ network (inclusion)

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.

6.1.1 SmartStart adding (inclusion)

SmartStart enabled products can be added into a Z-Wave™ network by scanning the Z-Wave™ QR Code present on the Device with a gateway providing SmartStart inclusion. No further action is required, and the SmartStart device will be added automatically within 10 minutes of being switched on in the network vicinity.

1. With the gateway application scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list in the gateway.

2. Connect the Device to a power supply.

3. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

4. Adding will be initiated automatically within a few seconds after connecting the Device to a power supply, and the Device will be added to a Z-Wave™ network automatically.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

6.1.2 Adding (inclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2, etc.) 3 times within 3 seconds (this procedure puts the Device in Learn mode*). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

*Learn mode - a state that allows the Device to receive network information from the gateway.

6.1.3 Adding (inclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the adding process.

7. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Classic Exclusion

Removing the Device from a Z-Wave™ network (exclusion)

Note! The Device will be removed from your Z-wave™ network, but any custom configuration parameters will not be erased.

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.

6.2.1 Removing (exclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the removing process.

6. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.

6.2.2 Removing (exclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the removing process.

7. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Factory Reset Procedure

6.3 Factory reset

6.3.1 Factory reset general

After Factory reset, all custom parameters and stored values (kWh, associations, routings, etc.) will return to their default state. HOME ID and NODE ID assigned to the Device will be deleted. Use this reset procedure only when the gateway is missing or otherwise inoperable.

6.3.2 Factory reset with a switch/push-button

Note! Factory reset with a switch/push-button is only possible within the first minute after the Device is connected to a power supply.

1. Connect the Device to a power supply.

2. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 5 times within 3 seconds. The Device must receive on/off signal 5 times, which means pressing the push-button 5 times, or toggling the switch on and off 5 times.

3. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s.

4. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.3 Factory reset with the S button

Note! Factory reset with the S button is possible anytime.

1. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

2. Press the S button multiple times until the LED turns solid red.

3. Press and hold (> 2s) S button on the Device until the red LED starts blinking in Mode 3. Releasing the S button will start the factory reset.

4. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s.

5. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.4 Remote factory reset with parameter with the gateway

Factory reset can be done remotely with the settings in Parameter No. 120.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Color

If the product is only available in one color, pick the color from the list.

Electric Load Type

Select the electric load type(s) supported by the device.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.