Viewed products

Temperature sensor for...

Secure SES302 is the temperature...

Temperature sensor for indoor Secure SES302

View larger

Product Under Order

Temperature sensor for indoor Secure SES302

Reference SES302

Condition: New

Secure SES302 is the temperature sensor that allows measurements through auxiliary cables, NTC, sensors for tube and tank ...

More details

Out of stock

Remove this product from my favorite's list.
Add this product to my list of favorites.
Print

More info

Z-Wave temperature sensor

Secure SES302 is the probe that allows the measurement of the temperature of internal conditions.

It is powered by 2 AA batteries and is Z-Wave Plus certified.
In addition to its main function, it is possible to wire several Secure external probes in the module, either:

1 external NTC temperature sensor (SES001)
4 temperature sensors by cable for pipe or tank (SES002) connected by cables 1m
1 cable temperature sensor for pipe or tank (SES003) connected by a 4m cable

These modules are ideal for temperature measurement in applications with central heating controls or other similar application. Its user interface is simple, with a local push button and LED indicators on the back.

It is easy to include / exclude in a Z-Wave network.

CHARACTERISTICS:

Accurate measurement of temperature
Application in dynamic control systems for tanks / pipes / underfloor heating / ...
Possibility of external probe connection
Interproperable with Z-Wave certification products and systems
easy installation
Low battery report

TECHNICAL CHARACTERISTICS:

Type: Portable mounting / wall
Temperature measurement range: ± 0.5 ° C from 0 ° C to 40 ° C
the Z-Wave chip More
Frequency: 868.42 MHz
Power supply: 2x AA (LR6)
Range: up to 100 m outside
Protection: IP30
Dimensions: 86 x 85 x 30 mm

Extended Z-Wave info

Name: Environmental Sensor

Manufacturer:Secure Controls (UK)

Identifier:SES 302

Z-Wave Certification Number:ZC10-15010007

Hardware Plattform:ZM5202

FLiRS:NO

Role Type:Reporting Sleeping Slave

Short Description:The Environmental Sensor (SES 302) is a temperature sensor, which also supports four external digital temperature sensors or one external analog temperature sensor.

Description:The Environmental Sensor (SES 302) measures temperature. The sensor is battery-operated devices which transmit information to an associated device in a network. It can support either 1 thermistor (SES 001) or up to 4 external digital temperature sensors (SES 002/003). SES 302 operates on 2x AA batteries, providing a nominal life of 2 years (with on-board sensors operating with the default configuration).

Manual download HERE.

Group

Max Nodes

Description

Z-Wave Plus Lifeline, in which multilevel sensor report, Battery low alarm are reported. Each endpoint supports 1 association group.

Number

Size (Bytes)

Default Value

Name

Description

Delta Temperature

This Parameter is used to configure the delta based temperature report. To configure Delta temperature reporting to 2 °C. The value need to configured in device is 2/0.1 = 20. Controllers may only allow configuring signed values. In order to set values in the range 128…255, the value sent in the application shall be equal to desired value minus 256. For example, to set Delta Temperature to 130, it may be needed to set a value 130−256=−126.

Temp Reporting Intervals

This Parameter is used to configure the time interval based temperature report. Controllers may only allow configuring signed values. In order to set values in the range 128…255, the value sent in the application shall be equal to desired value minus 256. For example, to set Delta Temperature to 130, it may be needed to set a value 130−256=−126.

Exclusion

Step 1.On the Z-Wave controller, select exclusion for removing a device from the network.
Step 2: On the SES 302, press the button, hold and release after 1 second to send a request (Network Information Frame) to remove from the network. On successful exclusion the LED will flash 2 times. The total process can take up to 2 seconds. If the LED flashes 4-times this means that the exclusion process has failed, so try moving the SES 302 to another position and repeat the exclusion steps. The controller will show when the exclusion operation is successful.

Learn Mode (adding another controller)

Not applicable

Factory Reset

Please use this procedure only when the primary controller is missing or otherwise inoperable.
To reset the device to factory resst, press the button 3 times within 3 seconds it will put the device in factory default, that include setting all the configuration, Association to factory default and removing the device from Z-Wave network.

Additional Special Features

None

Inclusion

Step 1.On the Z-Wave controller, select Include for adding a device to the network.
Step 2: On the SES 302, press the button, hold and release after 1 second to send a request (Network Information Frame) to join the network. On successful inclusion the LED will flash 2 times. The total process can take up to 20 seconds. If the LED flashes 4-times this means that the inclusion process has failed, so try moving the SES 302 to another position and repeat the Inclusion steps. If the inclusion process fails again, the device may be already included in another network. So first exclude and then include the device. The controller will show when the inclusion operation is successful.

Device Wake-Up

Device can be wakeup by button press of more then one second, devcie will stay in wakeup state for about 10 seconds.
device will also wakeup on the every wakeup interval configured by controller. The minimum wakeup interval can be configured is 2 minutes and maximum wakeup interval can be configured is 24 hours in setps of one minte.
Default wakeup interval is 24 hours.