Aeotec Water Sensor 7 (700 Series) Sensor de inundación Z-Wave+ ver2

Características técnicas

Tecnología	Z-Wave Serie 700

Descripción

El detector de inundaciones, Aeotec Water Sensor 7 es un sensor de inundación, un sensor de fugas y un sensor de seguridad en un solo dispositivo.

Detección de fugas. Las fugas son la base de costosas facturas y daños cuando aparecen donde no deben. Al vigilar algo más que la presencia de líquido, el sensor de agua 7 Pro de Aeotec hace honor a su nombre al vigilar la ausencia de agua. Cuando se utiliza para supervisar tanques o fosas, el Aeotec Water Sensor 7 Pro puede alertarle cuando los niveles de agua son demasiado bajos y activar rutinas de automatización.

El Aeotec Water Sensor 7 Pro no sólo controla las fugas de agua. Una vez conectado a su sistema de automatización Z-Wave, el Aeotec Water Sensor 7 Pro puede tomar medidas de protección para ayudar a limitar la cantidad de daños causados por goteos, fugas, roturas u otros flujos de agua. Por ejemplo, en caso de rotura de una tubería, el dispositivo inteligente puede ordenar a las válvulas de agua inteligentes, incluidas las instaladas en la tubería principal, que se cierren automáticamente.

Gestión de la calefacción. El Aeotec Water Sensor 7 Pro supervisa la temperatura de la habitación para controlar y gestionar los sistemas de calefacción o refrigeración conectados.

Gestión de la calidad del aire. Además de controlar la temperatura ambiente, el Aeotec Water Sensor 7 Pro mide la humedad relativa de la habitación. Con la monitorización de la humedad en tiempo real, el dispositivo inteligente puede utilizarse para gestionar automáticamente la calidad del aire de una habitación, activando los extractores y los humidificadores o deshumidificadores.

Características destacadas:

Sonda con sensor para la detección de fugas en zonas de difícil acceso

SIN Control de temperatura ni HUMEDAD
Hasta 5 años de duración de la batería
Compatible con Aeotec Smart Home Hub
Tecnología Gen7 (serie Z-Wave 700)
SmartStart
Z-Wave Plus V2
Aalimentación: Batería de litio CR123A

Información Ampliada Z-Wave (Inglés)

Nombre: Water Sensor 7 Pro

Fabricante:Aeotec

Identificador:ZWA019-C

Número de Certificación Z-Wave:ZC12-20060068

Plataforma Hardware:ZGM130

FLiRS:NO

Tipo de Role:Reporting Sleeping Slave

Descripción Corta:The Aeotec Water Sensor 7 Pro detects any liquid, which is spreaded by a leakage or other damage. It also measures the humidity and temperature of its environment.

Descripción:The Water Sensor 7 pro brings more safety into your home. With its flexible sensor probe and the sensitive sensor point it detects the presence and absence of water at any given location. Furthermore the Watersensor 7 pro is enabled to accurately measure the temperature and humidity of its environment, so you are always informed about your room climate. Thanks to the latest Z-Wave 700 series technology, the Water Sensor 7 is distinguished with and increased range, S2 Security, OTA FW update and SmartStart.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Lifeline association to gateways

2

5

Control devices when water leakage is detected

3

5

Sends out alarm message when water leakage is detected

4

5

Sends out alarm messages when tamper is tripped

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

10

2

0

Time Delay of "Off" command frame

Off command is sent after a delay defined in this parameter.

11

2

0

Delay of Tamper Alarm Cancellation

Time a tamper alarm is delayed.

12

1

Reporting Tamper Alarm Cancellation

This parameter defines if the alarm cancellation event is reported.

16

1

20

Minimum Temperature change to report

This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 18, may still be active.

17

1

5

Minimum humidity change to report

This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 18, may still be active.

18

2

43200

Temperature and Humidity Periodic Reports

This parameter defines the time interval to send an unsolicited report. If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 16 and 17, may still be active.

255

4

0

Reset Parameter

This parameter helps reset configuration parameters and the device to factory defaults 1 - 1431655764 (0x55555554) - Reset all Parameter settings to their default settings. 1431655765 - Completely factory reset sensor and send device reset locally notification.

3

1

7

Visual LED Indications

This parameter defines when LEDs will indicate events. Disabling all indications may extend battery life. Value 0 means - No Indications.

4

1

0

Range Test after double click

Allows to enable the activation of a Z-Wave range test with double clicking the tamper switch.

5

1

0

2nd Association Group Trigger

This parameter defines the status of the magnet switch that causes sending a BASIC command to all devices of Association Group 2.

6

1

2

Command Sent to Devices of Association Group 2

This parameter defines which commands is sent to 2nd Association Group

7

1

255

BASIC command "On event" value

This is the BASIC command value sent in case of "On" event.

8

1

0

BASIC command "Off event" value

This is the BASIC command value sent in case of "Off" event.

9

2

0

Time Delay of "On" command frame

On command is sent after a delay defined in this parameter.

Association Group Information V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Battery

COMMAND_CLASS_BATTERY

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Multilevel V11

COMMAND_CLASS_SENSOR_MULTILEVEL_V11

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Wake Up V2

COMMAND_CLASS_WAKE_UP_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

Scan the QR code inside the battery compartment of the device and your controller will add the device automatically when powered up.

Classic Inclusion

Inclusion

1. Open the housing.

2. Remove the battery protection.

3. Press the tamper on the side of the appliance three times quickly.

Classic Exclusion

Exclusion

1. Open the housing.

2. Press the tamper on the side of the appliance three times quickly.

Wake-Up Procedure

The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action: Press the tamper once

Factory Reset Procedure

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the GREEN LED blinks once.

Other Special Features

- The product is able to perform a range test to the gateway by setting parameter 4 as described in the manual

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Battery Type

Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

Color

If the product is only available in one color, pick the color from the list.

Battery Quantity

Enter the number of batteries of the designated type that the product uses.