AEOTEC - WATER SENSOR 6 Detector de agua Z-Wave

Características técnicas

Tecnología	Z-Wave Plus

Descripción

Muchas personas protegen su hogar de diferentes maneras con sensores de humo, cerraduras de puertas y sistemas de seguridad. Pero los peligros que corre por el agua sobre todo la gente subestiman.

Con el Sensor de agua 6 de Aeotec, se asegura de que el agua se dañe perfectamente. El sensor no visible detecta cantidades minúsculas de líquidos que pueden ser causadas por una pequeña fuga en la tubería de agua. Una bañera o un fregadero con sobredescarga no causa grandes daños porque el sensor puede enviar una alerta antes de que sea demasiado tarde.

En combinación con otros dispositivos en su red Z-Wave, puede apagar dispositivos eléctricos, cerrar válvulas de agua o encender bombas.

Gracias a la forma compacta del Sensor de agua 6, es posible colocarlo casi en cualquier lugar que desee. Además, contiene adicionalmente un sensor de vibración que detecta el sabotaje y los eventos de emergencia, así como un sensor de temperatura.

caracteristicas:

Sensor de agua con vibración integrada y sensor de temperatura
Detecta cantidades minúsculas de líquidos de 0,5 mm
Tamaño compacto
Fuente de alimentación: 1x batterie (CR123A)
Duración de la batería: aprox. 2 años
Tecnología inalámbrica: Z-Wave Plus

Información Ampliada Z-Wave (Inglés)

Nombre: Water Sensor 6

Fabricante:Aeotec

Identificador:ZW122-C

Número de Certificación Z-Wave:ZC10-17055615

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Reporting Sleeping Slave

Descripción Corta:Aeon Labs Water Sensor 6 is a Z-Wave water sensor, which can detect whether there is water leak in some places of your home.

Descripción:Aeotec by Aeon Labs Water Sensor 6 brings intelligence to a new level, one that is suited to both safety and convenience. It contains 4 sensing points, which would be more accurately to detect the presence and absence of water or detect whether there is water leak in some places of your home. The Water Sensor 6 has an inbuilt buzzer that can play alarm sounds to let you know when the water is detected. The Water Sensor 6 is also a security Z-Wave device that supports Over The Air (OTA) for firmware updates.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Lifeline group. 1. The Battery Report or Multilevel Sensor Report (Configurable) can be sent to the associated nodes in group 1. 2. When the water leak is detected, the Notification Report will be send to the associated nodes in group 1. 3. When the Water Sensor is reset, the Device Reset Locally CC will be send to the associated nodes in group 1.

2

5

Send the configuration parameter 0x88 to the associated nodes in group 2.

3

5

Send Basic Set (configured by parameter 0x58) to the associated nodes in Group 3 when the Sensor probe 1 is triggered.

4

5

Send Basic Set (configured by parameter 0x59) to the associated nodes in Group 4 when the Sensor probe 2 is triggered.

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

10

4

101968650

Set the alarm time for the Buzzer when the sensor is triggered.

101

1

3

To set what unsolicited report would be sent to the Lifeline group.

111

4

3600

To set the interval time of sending reports in Report group 1

To set the interval time of sending reports in Report group 1. Note: 1. The unit of interval time is second if USB power. 2. If battery power, the minimum interval time is equal to Wake Up interval set by the Wake Up CC.

135

1

To set which sensor report can be sent when the water leak event is triggered and if the receiving device is a non-multichannel device.

136

1

0

When the parameter 0x87 is set to 2 or 3, it can get the sensor probes’ status through this configuration value.

When the parameter 0x87 is set to 2 or 3, it can get the sensor probes’ status through this configuration value. Note: This parameter is a Get- only parameter.

2

1

0

Enable/Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.

201

2

1

Temperature sensor calibration

Temperature sensor calibration. Note: 1. High byte is the calibration value. Low byte is the unit (0x00=Celsius, 0x01=Fahrenheit) 2. The calibration value (high byte) contains one decimal point. E.g. if the value is set to 20 (0x1400), the calibration value is 2.0 ℃ (EU/AU version) or if the value is set to 20 (0x1401), the calibration value is 2.0 ℉(US version) 3. The calibration value (high byte) = standard value - measure value. E.g. If measure value =25.3℃ and the standard value = 23.2℃, so the calibration value= 23.2℃ - 25.3℃= -2.1℃ (0xEB). If the measure value =30.1℃ and the standard value = 33.2℃, so the calibration value= 33.2℃ - 30.1℃=3.1℃ (0x1F).

252

1

0

Enable/disable all configuration parameters to be locked

Enable/disable all configuration parameters to be locked.

255

4

0

Reset to factory defaults.

39

1

20

Configure the default low battery value.

Configure the default low battery value. When the current battery level is lower than this value, it will send out the low battery alarm.

48

1

0

Enable/disable the sensor report

49

4

68157696

Set the upper limit value (overheat).

50

4

20971776

Set the lower limit value (under heat)

57

2

5121

Set the recover limit value of temperature sensor.

Note: 1. When the current measurement <= (Upper limit – Recover limit), the upper limit report is enabled and then it would send out a sensor report when the next measurement is more than the upper limit. After that the upper limit report would be disabled again until the measurement <= (Upper limit – Recover limit). 2. When the current measurement >= (Lower limit + Recover limit), the lower limit report is enabled and then it would send out a sensor report when the next measurement is less than the lower limit. After that the lower limit report would be disabled again until the measurement >= (Lower limit + Recover limit). 3. High byte is the recover limit value. Low byte is the unit (0x01=Celsius, 0x02=Fahrenheit).

64

1

Set the default unit of the automatic temperature report in parameter 101-103.

8

1

30

Set the timeout of awake after the Wake Up CC is sent out..

84

1

0

Get the state of tilt sensor

Get the state of tilt sensor. Note: this is a Get-only parameter.

86

1

Enable/ disable the buzzer.

87

4

55

To set which sensor is triggered the buzzer will alarm.

88

1

0

To set which value of the Basic Set will be sent to the associated nodes in association Group 3 when the Sensor probe 1 is triggered.

89

1

0

To set which value of the Basic Set will be sent to the associated nodes in association Group 4 when the Sensor probe 2 is triggered.

9

2

0

Report the current power mode and the product state for battery power mode

Report the current power mode and the product state for battery power mode. Note: this parameter cannot be used as Set usage.

94

1

0

To set which power source level is reported via the Battery CC.

Basic

COMMAND_CLASS_BASIC

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Battery

COMMAND_CLASS_BATTERY

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V2

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Notification V4

COMMAND_CLASS_NOTIFICATION_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Sensor Multilevel V5

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

Version V2

COMMAND_CLASS_VERSION_V2

Wake Up V2

COMMAND_CLASS_WAKE_UP_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset

Press and hold the Action Button that you can find on the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.

Device Wake-Up

Pressing the Action Button once will trigger sending the Wake up notification command. If press and hold the Z-Wave button for 3 seconds, the Water Sensor will wake up for 10 minutes.

Additional Special Features

Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

Inclusion

Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action Button that you can find on the product.

Exclusion

Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action Button that you can find on the product.

Battery Quantity

Enter the number of batteries of the designated type that the product uses.

Battery Type

Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.