NODON interruptor de pared Z-Wave Plus (Blanco)

1

1

Z-Wave Plus® Lifeline. This group is used to report information of the OCTAN Remote to the Main Controller of the network.

2

8

Button 1 – MONO – Controlled nodes • A short press will activate (ON) your associated devices • A second short press will deactivate (OFF) your associated devices. If some of the associated devices have dimming features (light dimmer, roller shutter, etc.): • A long press will dim up your associated devices (light, roller shutter, etc.) until you release the button • A second long press on the same button will dim down your associated devices (light, roller shutter, etc.) until you release the button.

3

8

Button 2 – MONO – Controlled nodes • A short press will activate (ON) your associated devices • A second short press will deactivate (OFF) your associated devices. If some of the associated devices have dimming features (light dimmer, roller shutter, etc.): • A long press will dim up your associated devices (light, roller shutter, etc.) until you release the button • A second long press on the same button will dim down your associated devices (light, roller shutter, etc.) until you release the button.

4

8

Button 3 – MONO – Controlled nodes • A short press will activate (ON) your associated devices • A second short press will deactivate (OFF) your associated devices. If some of the associated devices have dimming features (light dimmer, roller shutter, etc.): • A long press will dim up your associated devices (light, roller shutter, etc.) until you release the button • A second long press on the same button will dim down your associated devices (light, roller shutter, etc.) until you release the button.

5

8

Button 4 – MONO – Controlled nodes • A short press will activate (ON) your associated devices • A second short press will deactivate (OFF) your associated devices. If some of the associated devices have dimming features (light dimmer, roller shutter, etc.): • A long press will dim up your associated devices (light, roller shutter, etc.) until you release the button • A second long press on the same button will dim down your associated devices (light, roller shutter, etc.) until you release the button.

6

8

Buttons 1&3 – DUO – Controlled nodes • A short press on button 1 will activate (ON) your associated devices. • A short press on button 3 will deactivate (OFF) your associated devices. If some of the associated devices have dimming features (light dimmer, roller shutter, etc.): • A long press on button 1 will dim up your associated device (light, roller shutter, etc.) until you release the button. • A long press on button 3 will dim down your associated device (light, roller shutter, etc.) until you release the button.

7

8

Buttons 2&4 – DUO – Controlled nodes • A short press on button 2 will activate (ON) your associated devices. • A short press on button 4 will deactivate (OFF) your associated devices. If some of the associated devices have dimming features (light dimmer, roller shutter, etc.): • A long press on button 1 will dim up your associated device (light, roller shutter, etc.) until you release the button. • A long press on button 3 will dim down your associated device (light, roller shutter, etc.) until you release the button.

1

1

0

Buttons 1&3 Profile

To set-up the profie of buttons 1 & 3s

2

1

0

Buttons 2&4 Profile

To set-up the profie of buttons 2 & 4

3

1

0

Scene Type

To choose the way of sending Scene to the gateway

4

1

0

Button 1 Configuration

To set-up the how button 1 behaves, when set in MONO Profie

5

1

0

Button 2 Configuration

To set-up the how button 2 behaves, when set in MONO Profie

6

1

0

Button 3 Configuration

To set-up the how button 3 behaves, when set in MONO Profie

7

1

0

Button 4 Configuration

To set-up the how button 4 behaves, when set in MONO Profie

8

1

0

Led Management

How to set up LED behaviour

Controller Inclusion

1- Push 3 times (quickly) on the button 3. The LED blinks in blue.

2- Place the device you want to add in “Learning” Mode. To do so, please refer to your device’s user guide. The LED blinks in green to confirm the inclusion.

Note: If you wish to include and associate a device, please refer to ""Other Special Features""

Controller Exclusion

1- Push 3 times (quickly) on the button 2. The LED blinks in blue.

2- Place the device you want to remove in “Learning” Mode. To do so, please refer to your device’s user guide. The LED blinks in green to confirm the exclusion.

Factory Reset

Simultaneously push on buttons 3 and 4, during 1 second. The LED will blink red and green to validate the factory reset.

A factory reset will completely delete the memory of the wall switch and restore all parameters to default value.
In ""Standalone"" Mode, make sure to remove all the devices added or associated in the wall switch's network before performing a factory reset.
In ""Gateway"" Mode, use the factory reset procedure only when the primary controller (i.e the Gateway) is missing or defective. Reset the wall switch does not mean that it has been removed from the primary controller memory. Remove the wall switch (through the primary controller) before performing a factory reset.

Additional Special Features

Association, in ""Standalone"" mode is performed in 3 steps:

1- Push 3 times (quickly) on the button 1 to activate the ""Association” Mode. The LED glows in blue.

2- Choose which button will control your device.
• A short press on one of the buttons of the wall switch (1, 2, 3 or 4) will activate the MONO Profile. The pressed button will then control your device.
• A long press on the button 1 will activate the DUO Profile, combined with the button 3. The button 1 (ON) and button 3 (OFF) will then control your device.
• A long press on the button 2 will activate the DUO Profile, combined with the button 3. The button 2 (ON) and button 4 (OFF) will then control your device.
The LED blinks in blue to confirm your choice.

3-Place the device you want to associate in “Learning” Mode. To do so, please refer to your device’s user guide. The LED of the wall switch blinks green to confirm the association process

Careful: In case of a too long association process or others problems during the process, the LED will blink red (Timeout). Please restart the procedure.

Once the association is validated, your wall switch is able to control your device. Different actions are possible.

Device Wake-Up

When the product in ""Gateway"" mode, any action on button will send a wake up notification to the gateway.

Learn Mode (adding another controller)

1- Place your home automation gateway into “Inclusion” Mode. To do so, please refer to your gateway’s user guide.

2- Simultaneously push on buttons 1 and 2, during 1 second. The LED glows in pink to confirm the selection.

3- Push on button 1. The LED blinks in pink to confirm your choice.

4- The LED blinks in green to confirm the procedure