Productos más vistos

FIBARO - Walli Dimmer

El regulador FIBARO Walli Dimmer es...

EN OFERTA

Ver más grande

Previo

FIBARO - Walli Dimmer

Referencia FGWDEU-111

Estado: Nuevo

El regulador FIBARO Walli Dimmer es un regulador inteligente con interruptor de luz integrado. Compatible con Z-Wave+.

Más detalles

Sin Stock

Eliminar de mis favoritos
Agregar este producto a mis favoritos
Imprimir

Características técnicas

Tecnología	Z-Wave Plus
Característica	Dimmer

Descripción

Interruptor de atenuación inteligente Z-Wave+ Fibaro Walli Dimmer

FIBARO Walli Dimmer es un dimmer inteligente con interruptor de luz integrado. Funciona con fuentes de iluminación disponibles en el mercado, tales como: LEDs, lámparas compactas, bombillas tradicionales y lámparas halógenas. El dispositivo está equipado con funciones de calibración y medición automáticas para la potencia activa y la energía.

Diseño único y tecnología excepcional

La serie completa de conectores e interruptores inteligentes FIBARO basados en la tecnología Z-Wave proporcionará a su hogar una inteligencia versátil. El aspecto de la serie está inspirado en una perla - su sofisticación atemporal y su bella forma que completa cualquier interior.

Fibaro Walli

Anillo LED a juego con su hogar

Elige tu color favorito

Seleccione el color del anillo LED para adaptarlo a sus preferencias personales.

Botón de doble retroiluminación

Utilice dos colores de retroiluminación donde quiera - un color diferente en la parte inferior y otro en la parte superior para ver el estado exacto del dispositivo.

Una visión general del consumo de energía

Controle la cantidad de energía que consumen los equipos de su hogar.

Componentes fiables y detalles llamativos

En FIBARO, calidad y diseño únicos siempre van de la mano. La línea Walli ha sido diseñada para mejorar el confort y la seguridad de su familia durante muchos años.

Fibaro Walli

Pulsaciones al gusto

Configure el botón del conmutador Walli para aprovechar al máximo sus asombrosas capacidades.

Un solo clic para encender la luz, un doble clic para apagarla, un triple clic para encender la escena "Fun", una pulsación mantenida durante un 60% de intensidad de luz.

Compatible con productos de otros fabricantes

FIBARO Walli es compatible (con adaptadores) con placas frontales de otros fabricantes: GIRA - Sistema 55, Legrand - Céliane, Schneider - Odace. Si está conectado a enchufes e interruptores existentes, equípelos con una pieza integrada inteligente y disfrute de las características de una casa inteligente sin tener que reemplazar el panel frontal.

Fibaro Walli

Gestionar toda la casa con voz

Los interruptores inteligentes y tomas de corriente de Walli son totalmente compatibles con los famosos asistentes de voz de Google Assistant y Amazon Alexa. Gestión de voz fácil y cómoda de toda la casa.

Estar con su hogar dondequiera que esté

La aplicación móvil FIBARO Home Center le permite gestionar interruptores y tomas inteligentes con su smartphone, tablet o smartwatch. Mantenga todo bajo control como un jefe.

Consumo de energía controlado

Eche un vistazo a su hogar, analice el consumo de energía de sus electrodomésticos y optimice sus gastos como siempre ha querido.

Da un paso adelante hacia el futuro

La serie Walli de FIBARO incluye interruptores y tomas de corriente clásicas y no inteligentes para mantener constante la estética de su hogar. Elíjalos como usted desee y disfrute de un diseño y características únicas.

FUNCIONES:

Gestión remota de la iluminación.
Control de la luz a través de comandos de voz.
Adaptación del anillo luminoso a las preferencias del usuario.
Notificaciones de averías de equipos eléctricos.
Control del consumo de energía.

ESPECIFICACIONES TÉCNICAS

Alimentación: 110-230V 50 / 60Hz
Corriente nominal de carga:
Resistivo: incandescente y halógeno 0.22-1.52A (50-350W)
Resistencia capacitiva: lámpara de tubo fluorescente (compacto / balasto electrónico), transformador electrónico, LED 0.22-1.3A (30-300VA)
Resistivo-inductivo: transformadores ferromagnéticos 0.22-1.3A (30-300VA)
Con FIBARO Bypass 2: lámpara de tubo fluorescente o LED (factor de potencia > 0,5) 0,022-0,22A (5-50W)
Frecuencia de radio: 868.0-868.6 MHz
Alcance: hasta 40 m en interiores (dependiendo del terreno y de la estructura del edificio)
Potencia máxima de transmisión: + 6dBm
Temperatura de funcionamiento: 0-35 ° C
Humedad ambiente: 10-95% RH sin condensación
Para instalación en cajas: Ø = 60mm, profundidad ≥ 40mm
Dimensiones (Al x An x Pr): 86 x 86 x 51mm

Toda la documentación e instrucciones de los productos Fibaro están disponibles en el sitio web manuals.fibaro.com

Información Ampliada Z-Wave (Inglés)

Nombre: Wall Dimmer

Fabricante:FIBARO

Identificador:FGWDEU-111

Número de Certificación Z-Wave:ZC10-19056515

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:FIBARO Walli Dimmer is a smart wall dimmer designed to control light source via Z-Wave network.

Descripción:FIBARO Walli Dimmer is a smart wall dimmer designed to control light source via Z-Wave network. It measures active power and energy consumed by the controlled load. You can install it with provided cover plate or other compatible. Main features of FIBARO Walli Dimmer: - Can be used for dimming: o 110/230V operated conventional incandescent and halogen, o 12V operated ELV halogen lamps and dimmable LED bulbs (with electronic transformers), o 12V operated MLV halogen lamps (with ferromagnetic transformers), o dimmable LED bulbs, o dimmable compact fluorescent CFL tube lamps, o supported dimmable light sources (power factor > 0.5) with minimal power of 5VA using FIBARO Bypass 2. - Can be used for switching: o compact fluorescent CFL tube lamps with electronic ballast, o fluorescent tube lamps with electronic ballast, o LED bulbs (power factor > 0.7), o supported light sources (power factor > 0.5) with minimal power of 5VA using FIBARO Bypass 2. - Uses different operating modes: o „Trailing edge” for resistive loads (R) o „Trailing edge” for resistive-capacitive loads (RC) o „Leading edge” for resistive-inductive loads (RL) - Can be used with provided cover plate or one of the following: o GIRA – System 55 (Standard 55, E2, Event, Event Clear), o Legrand – Céliane, o Schneider – Odace. - Active power and energy consumption metering. - Can be installed in two and three-wired configuration. - Calibrates automatically to the connected light source. - Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption. - Works as Z-Wave signal repeater (all non-battery operated devices within the network will act as repeaters to increase reliability of the network). - May be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).

2nd association group – “On/Off” is used to turn the associated devices on/off reflecting button operation (uses Basic command class).

3rd association group – “Dimmer” is used to change level of associated devices reflecting button operation (uses Switch Multilevel command class).

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

Remember device state

This parameter determines how the device will react in the event of power supply failure (e.g. power outage).

3500

LED frame – power limit

This parameter determines maximum active power. Exceeding it results in the LED frame flashing violet. Function is active only when parameter 11 is set to 8 or 9.

LED frame – colour when ON

This parameter defines the LED colour when thedevice is ON. When set to 8 or 9, LED frame colour will change depending on he measured power and parameter 10. Other colours are set permanently and do not depend on power consumption.

LED frame – colour when OFF

This parameter defines the LED colour when the device is OFF.

100

LED frame – brightness

This parameter allows to adjust the LED frame brightness.

150

Minimum brightness level

This parameter is set automatically during the calibration process, but can be changed manually after the calibration.

151

Maximum brightness level

This parameter is set automatically during the calibration process, but can be changed manually after the calibration.

152

Incandescence level of dimmable compact fluorescent lamps

The virtual value set as a percentage level between parameters MIN (1%) and MAX. (99%). The device will set to this value after the first switch on. It is required for warming up and switching dimmable compact fluorescent lamps and certain types of light sources.

153

Incandescence time of dimmable compact fluorescent lamps

This parameter determines the time required for switching compact fluorescent lamps and certain types of light sources. Setting this parameter to 0 will disable the incandescence functionality.

154

Automatic control – dimming step size

This parameter defines the percentage value of dimming step during the automatic control.

155

Automatic control – time of dimming step

This parameter defines the time of performing a single dimming step set in parameter 154 during the automatic control.

156

Manual control – dimming step size

This parameter defines the percentage value of the dimming step during the manual control.

157

Manual control – time of dimming step

This parameter defines the time of performing a single dimming step set in parameter 156 during the manual control.

158

Auto-off functionality

This parameter allows to automatically switch off the device after a specified time from switching the light source on. It may be useful when the device is installed in the stairway.

159

Force auto-calibration

Changing value of this parameter will force the calibration process. During the calibration parameter is set to 1 or 2 and switched to 0 upon completion.

160

Auto-calibration status (read-only parameter)

This parameter determines operating mode of the device (automatic/manual settings).

161

Burnt out bulb detection

This parameter defines percentage power variation (compared to power consumption measured during the calibration) to be interpreted as load error/burnt out bulb.

162

Time delay of a burnt out bulb and overload detection

This parameter defines detection delay for the burnt out bulb (parameter 161) and overload (parameter 2).

163

255

First button – Switch ON value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group.

164

Second button – Switch OFF value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group.

165

Double click – set level

This parameter defines brightness level set after double-clicking any of the buttons. The same value is also sent to devices associated with 2nd and 3rd association group.

170

Load control mode

This parameter allows to set the desired load control mode. Auto-calibration sets value of this parameter to 2 (control mode recognized during auto-calibration), but the installer may force control mode using this parameter. After changing parameter value, turn the load OFF and ON to change control mode.

171

Load control mode recognized during auto-calibration (read only)

This parameter allows to read load control mode that was set during auto-calibration.

172

ON/OFF mode

This mode is necessary while connecting non-dimmable light sources. Setting this parameter to 1 automatically ignores brightening/dimming time settings. Forced auto-calibration will set this parameter’s value to 2.

173

Dimmability of the load (read only)

This parameter allows to read if the load detected during calibration procedure is dimmable.

174

Soft-start functionality

This parameter allows to set time required to warm up the filament of halogen bulb.

175

Auto-calibration after power on

This parameter determines the trigger of auto-calibration procedure, e.g. power on, load error, etc.

176

Behaviour after OVERCURRENT or SURGE

Error occurrences related to surge or overcurrent results in turning off the output to prevent possible malfunction. By default the device performs three attempts to turn on the load (useful in case of temporary, short failures of the power supply).

177

255

Brightness level correction for flickering loads

Correction reduces spontaneous flickering of some capacitive loads (e.g. dimmable LEDs) at certain brightness levels in 2-wire installation. In countries using ripple-control, correction may cause changes in brightness. In this case it is necessary to disable correction or adjust the time of correction for flickering loads.

178

Method of calculating the active power

This parameter defines how to calculate active power. It is useful in a case of 2-wire connection with light sources other than resistive.

179

Approximated power at the maximum brightness level

This parameter determines the approximate value of the power that will be reported by the device at its maximum brightness level.

3500

Overload safety switch

This function allows to turn off the controlled device in case of exceeding the defined power. Controlled device can be turned back on via the button or sending a control frame.

Buttons orientation

This parameter allows reversing the operation of the buttons.

Alarm configuration - 1st slot

This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.

Alarm configuration - 2nd slot

Alarm configuration - 3rd slot

Alarm configuration - 4th slot

Alarm configuration - 5th slot

600

Alarm configuration – duration

This parameter defines duration of alarm sequence. When time set in this parameter elapses, alarm is cancelled, LED frame and relay restore normal operation, but do not recover state from before the alarm.

First button – scenes sent

This parameter determines which actions result in sending scene IDs assigned to them. Values can be combined (e.g. 1+2=3 means that scenes for single and double click are sent). Enabling scenes for triple click disables entering the device in learn mode by triple clicking.

Second button – scenes sent

Power reports – include self-consumption

This parameter determines whether the power measurements should include power consumed by the device itself.

Power reports – on change

This parameter defines minimal change (from the last reported) in measured power that results in sending new report. For loads under 50W the parameter is irrelevant, report are sent every 5W change.

3600

Power reports – periodic

This parameter defines reporting interval for measured power. Periodic reports are independent from changes in value (parameter 61).

Energy reports – on change

This parameter defines minimal change (from the last reported) in measured energy that results in sending new report.

3600

Energy reports – periodic

This parameter defines reporting interval for measured energy. Periodic reports are independent from changes in value (parameter 65).

Basic

COMMAND_CLASS_BASIC

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Information V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Central Scene V3

COMMAND_CLASS_CENTRAL_SCENE_V3

Configuration

COMMAND_CLASS_CONFIGURATION

CRC16 Encapsulation

COMMAND_CLASS_CRC_16_ENCAP

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Protection V2

COMMAND_CLASS_PROTECTION_V2

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Switch Multilevel V4

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Device Wake-Up

FIBARO Walli Dimmer is powered using DC power supply unit so it is always awake.

Factory Reset

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. Resetting to factory defaults does not reset energy consumption memory.

1. Quickly, three times click, then press and hold one of the buttons to enter menu.

2. Release the button when the device glows yellow.

3. Quickly click the button to confirm.

4. After a few seconds the device will be restarted, which is signalled with the red LED colour.

Please include a request to use the reset procedure only when the primary controller is missing or inoperable.

Exclusion

To remove the device from the Z-Wave network:

1. Set the main controller into remove mode (see the controller’s manual).

2. Quickly, three times click one of the buttons.

3. LED will start blinking yellow, wait for the removing process to end.

4. Successful removing will be confirmed by the Z-Wave controller’s message and red LED colour.

5. The device will start calibrating the load.

Inclusion

To add the device to the Z-Wave network manually:

1. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual).

2. Quickly, three times click one of the buttons.

3. If you are adding in Security S2 Authenticated, scan the DSK QR code or input the underlined part of the DSK (label on the bottom of the box).

4. LED will start blinking yellow, wait for the adding process to end.

5. Adding result will be confirmed by the Z-Wave controller’s message and the LED frame:

- Green - successful (non-secure, S0, S2 non-authenticated),

- Magenta - successful (Security S2 Authenticated),

- Red – not successful.

To add the device to the Z-Wave network using Smart Start:

1. Set the main controller in Security S2 Authenticated add mode (see the controller’s manual).

2. Scan the DSK QR code or input the underlined part of the DSK (label on the bottom of the box).

3. Power the device.

4. Wait for the calibration process to end. Light may blink, the device will be switched off once the process is completed.

5. Wait for the adding process to start (up to few minutes), which is signaled with yellow LED blinking.

6. Adding result will be confirmed by the Z-Wave controller’s message and the LED frame:

- Green - successful (non-secure, S0, S2 non-authenticated),

- Magenta - successful (Security S2 Authenticated),

- Red – not successful.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Loads Controlled

The number of different loads controllable by the product if it supports more than one.

Supported Meter Type

Indicate which type of metering is supported by the device.

Color

If the product is only available in one color, pick the color from the list.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).