Medidor de consumo eléctrico 3 pinzas Aeon Labs GEN5

Características técnicas

Tecnología Domótica	Z-Wave Plus
Característica	Medición de Consumo

Descripción

Las pinzas de monitorización de consumo de Energía Inteligente de Aeon Labs es un medidor de consumo electrico de bajo coste para la casa u oficina. Puede informar de manera inalámbrica del uso instantáneo de vatios y kWh y enviar al información al controlador domótico y puede instalarse fácilmente. Instalado en una caja de registro o cuadro electrico, el medidor de energía controlará el consumo total de electricidad utilizado por una edificacion entera, plantas o según circuitos. La pinza inteligente informará cuando el uso de energía vuelve a un punto de control, en vatios o kilovatios-hora, y en tiempo real. Así puede ver cuánta electricidad realmente usa y cuándo la usa. El controlador domotico podra presentarle la información almacenada a lo largo del tiempo en forma de graficas, dependiendo de lo que sea capaz de hacer el controlador domotico con el que trabaja....

El cuerpo principal está anclado utilizando un soporte trasero. El dispositivo se alimenta de una fuente de alimentación de CA normal. El dispositivo tiene una pinza e informa de W y kWH (hasta 60 Amperios).

Fácil de instalar, informa de forma inalámbica del consumo energético de toda la casa a un controlador domótico basado en Z-Wave: vatios y kW/h. Se conecta al cuadro eléctrico de la vivienda o comercio para controlar todo su consumo electrico, incluso en tiempo real. Por tanto es una herramienta perfecta para saber cuanta electricidad se consume y cuándo.

Este dispositivo funciona mediante protocolo Z-Wave, y ahi variantes de este mismo equipo de más o menos pinzas (en función de lo que se quiera controlar) y de diferente limite de amperaje. Permite conocer en tiempo real los consumos de una o varias fases de un cuadro o circuito eléctrico, y resulta una herramienta muy útil para recoger lecturas o estudios mas o menos constantes a los instaladores o gestores energéticos, pues permite llegar a conclusiones rápidamente y poder tomar medidas para reducir el gasto energético en electricidad.

Medidor consumo electrico

Monitorización Remota mediante medidor de consumo electrico vía Z-Wave

Medidor de energía para toda la casa o comercio de bajo coste (potencia y kWh)

Alimentado a 220V

Tecnología Z-Wave Plus

Información Ampliada Z-Wave (Inglés)

Nombre: Home Energy Meter Gen5

Fabricante:Aeotec

Identificador:ZW095-C

Número de Certificación Z-Wave:ZC10-16105288

Plataforma Hardware:ZM5202

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:Aeon Labs Home Energy Meter Gen5 is a smart energy meter, which can monitor the total amount of electricity of your home. This HEM G5 has 3 metering channels and supports the installation on 3 phases 4 wire or 3 phases 3 wire power system.

Descripción:Aeon Labs Home Energy Meter Gen5 is a Z-Wave device that can monitor the total amount of electricity of your home. It can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway). In near real-time you’ll have a full understanding of how much electricity you use and when you use it. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices. Also a tool that can be programmed, scheduled, controlled and communicated with from anywhere in the world.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Z-Wave Plus Lifeline. The automatic reports (configured by parameter 101/102/103) can be sent to the associated nodes in association group 1.

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

10

1

10

Percentage change in wattage to induce a automatic report

Percentage change in wattage to induce a automatic report for the power report of Clamp 2.

101

4

2

To set which report need to be sent.

To set which report need to be sent in Report group 1.

102

4

1

To set which report need to be sent.

To set which report need to be sent in Report group 2.

103

4

0

To set which report need to be sent.

To set which report need to be sent in Report group 3.

11

1

10

Percentage change in wattage to induce a automatic report

Percentage change in wattage to induce a automatic report for the power report of Clamp 3.

111

4

5

Set the interval time of sending report.

Set the interval time of sending report in Report group 1.

112

4

120

Set the interval time of sending report.

Set the interval time of sending report in Report group 2.

113

4

120

Set the interval time of sending report.

Set the interval time of sending report in Report group 3.

2

1

0

Set the energy detection mode for parameter 101 to 103.

Set the energy detection mode for the measure reports of parameter 101 to 103.

200

1

0

Partner ID

Partner ID.

252

1

0

Enable/Disable Lock Configuration

Enable/Disable Lock Configuration.

255

4

0

Reset to default factory setting

Reset to default factory setting.

3

1

Enable/disable selective reporting only when power change reaches a certain threshold or percentage

Enable/disable selective reporting only when power change reaches a certain threshold or percentage set in parameter 4 to 11.

4

2

50

Threshold change in wattage to induce a automatic report

Threshold change in wattage to induce a automatic report for total power report.

5

2

50

Threshold change in wattage to induce a automatic report

Threshold change in wattage to induce a automatic report for the power report of Clamp 1.

6

2

50

Threshold change in wattage to induce a automatic report

Threshold change in wattage to induce a automatic report for the power report of Clamp 2.

7

2

50

Threshold change in wattage to induce a automatic report

Threshold change in wattage to induce a automatic report for the power report of Clamp 3.

8

1

10

Percentage change in wattage to induce a automatic report

Percentage change in wattage to induce a automatic report for total power report.

9

1

10

Percentage change in wattage to induce a automatic report

Percentage change in wattage to induce a automatic report for the power report of Clamp 1.

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

CRC16 Encapsulation

COMMAND_CLASS_CRC_16_ENCAP

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V4

COMMAND_CLASS_METER_V4

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset

Press and hold the Action button that you can find on the product's housing for 10 seconds and then release. This procedure should only be used when the primary controller is inoperable.

Additional Special Features

Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

Inclusion

Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing.

Exclusion

Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing.

Supported Meter Type

Indicate which type of metering is supported by the device.

Color

If the product is only available in one color, pick the color from the list.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.