Aeotec Nano Shutter micromodulo persianas Z-Wave Plus

Características técnicas

Tecnología	Z-Wave Plus

Descripción

Nano Shutter. Los controles del motor de su obturador están conectados en Z-Wave.
Las persianas de seguridad para tragaluces, aparatos electrónicos y muebles motorizados forman parte de un hogar moderno. Ahora, pueden ser parte de su hogar conectado.

El Nano Shutter se integra con los motores y los convierte en Z-Wave. Al instante, todo lo que están conectados puede controlarse de forma inalámbrica y automatizarse de manera inteligente gracias al Nano Shutter que se puede integrar con una amplia selección de dispositivos.

Fácil de instalar. Simple de controlar.
El Nano Shutter se conecta a los accesorios de su hogar controlados por un motor. Simplemente hace esto e inmediatamente hace que estos accesorios estén disponibles para el control, la automatización y la planificación a través de Z-Wave.

Puede conectarse para conectarse directamente al motor. Se puede conectar a cualquier interruptor de pared existente que controle el motor. Y se puede conectar en segundos a WallSwipe, lo que le permite mejorar aún más el Nano Shutter para tener un control táctil y gestual.

Una vez instalado, puede controlar el Nano Shutter a través de cualquier interruptor conectado y a través de Z-Wave a través de su puerta de enlace, su control remoto y la aplicación de su teléfono inteligente.

Hecho con experiencia.
El Nano Shutter está diseñado a partir de la misma experiencia de 10 años que se ha infundido en el Nano Dimmer y el Nano Switch. La experiencia que incluye la ingeniería del primer controlador de obturador Z-Wave; el micro controlador de motor.

Con esta experiencia, el Nano Shutter ofrece 3 nuevas mejoras esenciales para esta tecnología.

Mejor seguridad.
Para cualquier motor que controle puntos de acceso, como puertas y persianas de seguridad, el Z-Wave S2 es crucial. El S2 mejora el Nano Shutter con funciones de última generación contra la piratería, que incluyen el cifrado AES de 128 bits y el intercambio de claves ECDH.

Z-Wave Plus.
Además de su seguridad avanzada, el Z-Wave Plus Nano Shutter. La última versión de Z-Wave permite que el Nano Shutter controle los accesorios conectados con un tiempo de respuesta del 250% más rápido y un alcance inalámbrico del 67% más alto, hasta 150 metros.

60% más pequeño.
Diseñado para ser fácil de instalar, el obturador Nano también se ha diseñado para que sea más fácil de instalar. Con solo 43 x 20 cm, es 60% más pequeño que el Micro Motor Controller, lo que significa que es incluso más fácil de instalar detrás de los interruptores del motor.

Atención, este módulo requiere el neutro para funcionar.

FUNCIONES:

Ordene sus persianas o persianas de forma remota
Se instala detrás de un interruptor existente
Función arriba / abajo (sin posicionamiento)
Integra el chip serie Z-Wave 500.
Comunicación 250% más rápida en comparación con los dispositivos Z-Wave estándar
Soporta el marco de seguridad Z-Wave S2
Detección automática del tipo de interruptor.
Compatible con todos los controladores Z-Wave y Z-Wave +
Medida de la función de consumo instantáneo y acumulativo.
Conector para interruptor WallSwipe (próximamente)
Utilizar con interruptor de palanca o impulso
Pequeño, discreto y estético.
Facilidad de uso e instalación.

CARACTERÍSTICAS TÉCNICAS :

Tipo de módulo: receptor Z-Wave
Fuente de alimentación: 120-240VAC, 50 / 60Hz
Consumo de energía en espera: <0.8W
Cableado: 3 hilos, neutro requerido
Carga maxima: 2.5A
Indicador de estado: LED
Frecuencia: 868.42 Mhz
Distancia de transmisión: 150m en campo libre.
Dimensiones: 42.5mm x 40mm x 20mm
Temperatura de funcionamiento: 0-40 ° C
Humedad de funcionamiento: 8-80%
Certificaciones: FCC, UL, CE, ROHS

Información Ampliada Z-Wave (Inglés)

Nombre: Nano Shutter

Fabricante:Aeotec

Identificador:ZW141-C

Número de Certificación Z-Wave:ZC10-19126810

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:Aeotec New Generation motor controller

Descripción:Aeotec New Generation Nano Shutter 1. Used to control the motor of Curtain, support Shutter Mode and Venetian Mode . 2. Can be calibrated according to diff e rent curtains 3. Used to control other Z-Wave device directly. 4. Support S2, more safe and more re liable 5. Support SmartStart, faster inclusion

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Used for some commands auto sending when status changed.

2

5

Retransmit when receiving the follow commands

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

120

1

0

Switch Type of External Switch 1

Used to set Switch type of External Switch 1,and reports will return automatically during identify.

121

1

0

Switch Type of External Switch 1

Used to set Switch type of External Switch 1,and reports will return automatically during identify.

20

1

0

Motor Behavior After Power ON

Setting the Motor Behavior After Power ON.

22

1

0

Determine motor run direction

Note: 1.Motor will stop when receiving this command in moving; 2.This configuration will not change after network exclusion or Configuration Reset.

248

1

Function Setting of External Switch S1&S2

Used to Enable/Disable function of External Switch S1&S2. Note : This value can be combine, e.g. set to 3(1+2=3),means networking function and Reset function are both enable.

255

4

0

Reset Function

Used to reset configuration parameter value to default value or reset to factory default settings. Note： Parameter 0x16, 0x22, 0x23, 0x24, 0x25, 0x27, 0x28 will not reset to default value by this command.

34

2

150

Set the Blade Turn Time

This parameter is to config the blade turn time(unit = 0.01s),which works only for venetian mode.Details can be found in section 4.2 of Advanced information Product Manual. Note: For Venetian, if this value is set too large for blade turning, curtain may move upwards or downwards. Calibration need to work correctly.Or this setting will force the curtain to move up or down. This configuration will not change after network exclusion or Configuration Reset.

35

2

15000

Curtain Trip Time

Curtain Trip Time is about the run time of the curtain (unit = 0.01s). Details can be found in section 4.2 of Advanced information Product Manual. Note: For Venetian, if this value is set too large for blade turning, curtain may move upwards or downwards. Calibration need to work correctly.Or this setting will force the curtain to move up or down. This configuration will not change after network exclusion or Configuration Reset.

36

1

0

Enter/Exit Calibration

Note: Product will enter the right Curtain Mode after calibration, see Configuration 0x27(39)

37

1

0

User confirmation for Calibration

User confirmation for Calibration(set only)

38

1

0

Calibration Status Report

Return Calibration Status(Get or Report)

39

1

0

Cutain Mode Setting

Set the Curtain Mode. Note: 1. This Operation will enter repositioning automatically; 2. This configuration will not change after network exclusion or Configuration Reset.

40

1

Repositioning

Set to begin repositioning.

41

1

0

Repositioning Status Report

Used to Get repositioning Status.

42

1

Calibration Lock

Used to enable/disable calibration lock from different ways.

80

1

2

Switch Status Report Selection

Choose which report to send when switch status change

85

1

0

Extern Button Mode Setting

Extern Button Mode Setting Note: when setting value to 2, we advice not to set only one external switch to push button, do remember to change the controller channel before operating push button, or the curtain level will be wrong.

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Central Scene V3

COMMAND_CLASS_CENTRAL_SCENE_V3

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Powerlevel

COMMAND_CLASS_POWERLEVEL

Scene Activation

COMMAND_CLASS_SCENE_ACTIVATION

Scene Actuator Conf

COMMAND_CLASS_SCENE_ACTUATOR_CONF

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Switch Multilevel V4

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Classic Exclusion

3.6 How to Remove the device from Z-Wave network

1. Set your Z-Wave Controller into its 'Remove Device' mode in order to remove the product from your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.

2. Click Action Button/S1/S2(external switch need to be identified first) 6 times will enter exclusion mode.

3. If Removing fails, it will bright red light for 2s then turn back to Regular Light Mode, repeat steps 1-2. Contact us for further support if needed.

4. If Removing succeeds, it will alternate through a rainbow of colors. Now, it is removed from Z-Wave network successfully.

Other Special Features

Calibration for Shutter have 2 modes: Shutter Mode for Standard roller blind, and Venetian Mode for Venetian Blind. Shutter will record the Curtain Trip Time for Shutter mode and Curtain Trip Time + Blade Turn Time for Venetain Mode.

The detail can be found in section 4.2 Calibration in Advanced information Product Manual.

Where to find S2 DSK on product

There is no DSK on the product.QR code used for SmartStart inclusion. DSK code can be found on packaging.

Factory Reset Procedure

3.7 How to Factory Reset

Manually, press and hold the Action Button for at least 20s and then release. The LED indicator will alternate through a rainbow of colors, which indicates the reset operation is successful. Otherwise, please try again. Contact us for further support if needed.

Note:

1. This procedure should only be used when the primary controller is missing or inoperable.

2. Factory Reset will:

a) Remove the product from Z-Wave network;

b) Delete the Association setting;

Classic Inclusion

3.5.2 Classic inclusion Learn Mode

1. Set your Z-Wave Controller into its 'Add Device' mode in order to add the product into your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.

2. Make sure the product is powered. After powered up, Its LED will alternate through a rainbow of colors all the time.

3. Click Action Button once, it will quickly flash blue light for 30 seconds until it is added into the network.

4. If your Z-Wave Controller supports S2 encryption, enter the first 5 digits of DSK into your Controller's interface if /when requested. The DSK is printed on its housing.

5. If Adding fails, it will bright red light for 2s and then alternate through a rainbow of colors; repeat steps 1 to 4. Contact us for further support if needed.

6. If Adding succeeds, it will bright blue light for 2s and then turn to Motor Mode(green for runing, off for stop). Now, this product is a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your software's user guide for precise instructions.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Color

If the product is only available in one color, pick the color from the list.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.

Switch Load Capacity Current

The amount of switch load energy the product is rated for in Amps