Shelly Qubino Wave 2PM Micromódulo Relé doble medición consumo Z-Wave

Características técnicas

Tecnología	Z-Wave Serie 800

Descripción

Micromódulo Interruptor inteligente Z-Wave™, 2 canales 16 A de corriente en total (18 A de pico), con medición de potencia.

Controla a distancia dos aparatos eléctricos independientes (por ejemplo, luces) y supervisa su consumo de energía por separado y en total.

2 canales (2x 10 A, 16 A en total)
Medición de potencia en cada canal y en total
Consumo de energía extremadamente bajo: 0.3 W.
Banda de frecuencia Z-Wave: 868,4 MHz (países CEPT)
Última tecnología: Z-Wave Serie 800
Configuración automática con SmartStart
Seguridad 2 autenticada para el máximo nivel de seguridad
Admite actualizaciones de firmware por aire
Instalación sencilla en la mayoría de cajas eléctricas e interruptores estándar
Funciona con pasarelas certificadas Z-Wave y más de 4.000 dispositivos Z-Wave
*No se incluye una puerta de enlace (concentrador inteligente). Se requiere una pasarela (smart hub) para la configuración del dispositivo.

Funciona con cualquier pasarela Z-Wave
Wave 2PM es retrofit y está diseñado para encajar detrás de cualquier interruptor o enchufe, transformándolo instantáneamente en uno inteligente. Una vez instalado, inclúyalo en su red Z-Wave (se requiere pasarela Z-Wave) y controle los electrodomésticos conectados desde cualquier lugar utilizando su smartphone o tableta. Los dispositivos Shelly Qubino funcionan con más de 4000 dispositivos y pasarelas certificados Z-Wave.

Funciona con Z-Wave

Conecta Wave 2PM a tu red Z-Wave y contrólalo a distancia. Es compatible con todas las pasarelas Z-Wave certificadas.

Asociaciones

Establezca una comunicación directa entre los dispositivos de su red local Z-Wave y defina acciones personalizadas sin necesidad de un concentrador.

Monitorización de potencia

Wave 2PM proporciona una supervisión precisa del consumo de energía en cada canal por separado y en total.

Amplia gama de voltajes

Utilícelo para controlar una amplia gama de dispositivos y electrodomésticos.

Horarios inteligentes

Crea horarios personalizados alineados con tu rutina diaria o sincronízalos con la salida/puesta del sol para gestionar tu iluminación (requiere pasarela).

Escenas inteligentes

Configura escenas personalizadas combinando Wave 2PM con cualquier otro dispositivo Z-Wave (se requiere pasarela).

Un sinfín de aplicaciones de uso

Controla dos luces con un solo dispositivo

Wave 2PM te permite controlar a distancia dos luces u otros aparatos eléctricos y supervisar su consumo de energía. Utiliza el interruptor manual, la aplicación Smart Home, el sistema domótico o el control por voz. ¡Fácil, cómodo y energéticamente eficiente!

Controla tu consumo de energía y ahorra dinero

Con Wave 2PM puede medir con precisión el consumo de energía de cada canal por separado (W) y en conjunto (W, kWh). Controla el consumo en tiempo real de los dispositivos conectados y ajusta los patrones de uso para reducir fácilmente los costes de los servicios públicos.

Cree horarios que sigan su rutina diaria

Aumente la eficiencia energética de su hogar y simplifique su vida diaria. Programe sus luces para que se enciendan gradualmente cada mañana a las 7 o al atardecer, si la casa está ocupada. De este modo, tu casa puede seguir automáticamente tu rutina diaria y crear un ambiente que te convenga en un momento determinado del día.

El módulo Shelly Qubino Wave 2PM es un interruptor integrado Z-Wave 800 con dos salidas. El módulo admite la medición activa de energía y está diseñado para controlar dispositivos como luces, ventiladores, paneles infrarrojos, calefactores y otros aparatos eléctricos. Es posible controlar el módulo de forma inalámbrica a través de Z-Wave, así como mediante un interruptor de pared.

El módulo puede alimentarse con un voltaje de 110-240 V CA o 24 CC, lo que permite flexibilidad en el suministro eléctrico. La capacidad de carga máxima en CA es de 16 A y en CC de 10 A. Las salidas del Wave 2PM pueden conmutar 10A individualmente y 16A combinados.

Además, el módulo está equipado con varias funciones de protección, como protección contra sobrecalentamiento, sobretensión y sobrecorriente.

Características

Serie Z-Wave 800
Capacidad de carga máxima en CA: 16 A, en CC: 10 A
Protegido contra el sobrecalentamiento
Admite actualizaciones de firmware por aire (OTA)
Se puede utilizar con diferentes tipos de interruptores

ESPECIFICACIONES TECNICAS

Alimentación	110-240 V AC / 24 V DC +/-10%
Consumo	< 0.3 W
Medición de potencia (W)	Si
Voltaje Max del relé en AC	240 V
Max corriente del relé en AC	10 A por canal, 16 A total, 18 A de corriente de pico
Voltaje Max del relé en DC	30 V
Max corriente del relé en DC	10 A
Protección de sobrecalentamiento	Si
Protección de sobrecarga	Si
Distancia	Hasta 40 m en interior (131 ft.) (dependiendo de condiciones del local)
Repetidor Z-Wave™:	Si
CPU	Z-Wave™ S800
Ferecuencia Z-Wave™:	868,4 MHz (Europa)
Potencia máxima de radiofrecuencia transmitida en la banda de frecuencias(s)	< 25 mW
Tamaño (H x W x D)	37x42x16 ±0.5 mm / 1.46x1.65x0.63 ±0.02 in
Montaje	Caja de mecanismos o caja de registro
Par de apriete máx. de los terminales de tornillo	0.4 Nm / 3.5 lbin
Sección del conductor	0.5 a 1.5 mm² / 20 a 16 AWG
Longitud pelada del conductor	5 a 6 mm / 0.20 a 0.24 in
Material de la carcasa	Plástico
Color	Negro
Temperatura ambiente	-20°C to 40°C / -5°F to 105°F
Humedad	30% to 70% RH
Max. altitud	2000 m / 6562 pies

Información Ampliada Z-Wave (Inglés)

Nombre: Wave 1PM

Fabricante:Shelly Qubino

Identificador:QNSW-001P16EU

Número de Certificación Z-Wave:ZC14-23100356

Plataforma Hardware:EFR32ZG23A

FLiRS:NO

Tipo de Role:Always On End Node

Descripción Corta:The Device is a single product that enables the control of the on/off function for one electrical device such as bulb, ceiling fan, IR heater. It measures the power consumption of the connected device.

Descripción:The Device is a single product that enables the control of the on/off function for one electrical device such as bulb, ceiling fan, IR heater. It measures the power consumption of the connected device.

Grupo

Max Nodos

Descripción

1

9

2

9

3

9

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

1

2

SW1 Switch type

0 push, 1 toggle state, 2 toggle change

120

1

0

Factory reset

17

1

0

Restore state of O1 after power failure

0 restore, 1 no restore

19

2

0

Turn O1 OFF Automatically with timer

0 - 32535, 0 disabled

20

2

0

Turn O1 ON Automatically with timer

0 - 32535, 0 disabled

201

4

2147483647

Serial Number 1

202

4

2147483647

Serial Number 2

203

4

2147483647

Serial Number 3

23

1

0

O1 NO/NC

0 NO, 1 NC

25

1

0

Set timer units to Seconds or Milliseconds for O1

0 seconds, 1 millisecods

36

1

50

O1 Power report on change - percenatge

1-100 percentage, 0 disabled

39

1

30

O1 min reporting time

1-120 seconds, 0 disabled

91

4

0

Alarm conf. - Water

0 no action 1 open relay 2 close relay

92

4

0

Alarm conf. - Smoke

0 no action 1 open relay 2 close relay

93

4

0

Alarm conf. - CO

0 no action 1 open relay 2 close relay

94

4

0

Alarm conf. - Heat

0 no action 1 open relay 2 close relay

Association Group Information (AGI) V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Binary Switch V2

COMMAND_CLASS_SWITCH_BINARY_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V6

COMMAND_CLASS_METER_V6

Multi Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security 0

COMMAND_CLASS_SECURITY

Security 2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

When adding the Device to a Z-Wave network with a gateway supporting Security 2 (S2), the PIN Code of the Z-Wave Device Specific Key (DSK) is required. You can find it on the label on the side of the Device and a copy is inserted in the packaging, which must not be lost. Do not remove the Z-Wave DSK label from the Device. As a backup measure, use the label in the packaging.

The first five digits of the key are highlighted or underlined to help the user identify the PIN Code part of the DSK text. The DSK is additionally represented with a QR Code as shown on the image.

Classic Inclusion

6.1 Adding the Device to a Z-Wave™ network (inclusion)

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.

6.1.1 SmartStart adding (inclusion)

SmartStart enabled products can be added into a Z-Wave™ network by scanning the Z-Wave™ QR Code present on the Device with a gateway providing SmartStart inclusion. No further action is required, and the SmartStart device will be added automatically within 10 minutes of being switched on in the network vicinity.

1. With the gateway application scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list in the gateway.

2. Connect the Device to a power supply.

3. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

4. Adding will be initiated automatically within a few seconds after connecting the Device to a power supply, and the Device will be added to a Z-Wave™ network automatically.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

6.1.2 Adding (inclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2, etc.) 3 times within 3 seconds (this procedure puts the Device in Learn mode*). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

*Learn mode - a state that allows the Device to receive network information from the gateway.

6.1.3 Adding (inclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the adding process.

7. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Classic Exclusion

Removing the Device from a Z-Wave™ network (exclusion)

Note! The Device will be removed from your Z-wave™ network, but any custom configuration parameters will not be erased.

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.

6.2.1 Removing (exclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the removing process.

6. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.

6.2.2 Removing (exclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the removing process.

7. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Factory Reset Procedure

6.3 Factory reset

6.3.1 Factory reset general

After Factory reset, all custom parameters and stored values (kWh, associations, routings, etc.) will return to their default state. HOME ID and NODE ID assigned to the Device will be deleted. Use this reset procedure only when the gateway is missing or otherwise inoperable.

6.3.2 Factory reset with a switch/push-button

Note! Factory reset with a switch/push-button is only possible within the first minute after the Device is connected to a power supply.

1. Connect the Device to a power supply.

2. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 5 times within 3 seconds. The Device must receive on/off signal 5 times, which means pressing the push-button 5 times, or toggling the switch on and off 5 times.

3. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s.

4. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.3 Factory reset with the S button

Note! Factory reset with the S button is possible anytime.

1. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

2. Press the S button multiple times until the LED turns solid red.

3. Press and hold (> 2s) S button on the Device until the red LED starts blinking in Mode 3. Releasing the S button will start the factory reset.

4. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s.

5. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.4 Remote factory reset with parameter with the gateway

Factory reset can be done remotely with the settings in Parameter No. 120.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Color

If the product is only available in one color, pick the color from the list.

Electric Load Type

Select the electric load type(s) supported by the device.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.