Interruptor Z-Wave AEON LABS Heavy Duty Smart Switch precio en España

Características técnicas

Tecnología Domótica	Z-Wave Plus
Característica	Medición de Consumo

Descripción

Se trata de un interruptor Z-Wave Plus (GEN5), inteligente, del fabricante AEON LABS apto para grandes cargas (heavy duty) de hasta 40 amperios.

Interruptor inteligente Z-Wave Plus (GEN5) Aeotec de AEON LABS para grandes cargas (heavy duty) es un módulo interruptor que va a permitir controlar aparatos o grupos de aparatos con cargas máximas de hasta 9600W. Podrá controlar a distancia o automáticamente mediante eventos o escenas domóticas predefinidas a través de una Unidad de Control Z-Wave.

Gracias a sus funcionalidades de supervisión de la energía y planificación podrá ahorrar en electricidad de forma inmediata. Podrá recibir reportes de consumo electrico en tiempo real, podrá planificar y preveer los picos de consumo, etc. gracias a sus funcionalidadesd de control y ahorro eléctricos, hasta un máximo de 40 amperios de intensidad electrica.

Interruptor inteligente Z-Wave Plus (GEN5) de AEON LABS dispone de la tecnología Gen5 de Aeotec, que sobrepasa las prestaciones de todo lo conocido hasta el momento en Z-Wave. Está construido conforme a la serie 500 de Z-Wave, ofreciendo mejoras en el rendimiento de radio del 50% y de una velocidad de comunicacion del 250% más rápido respecto a productos precedentes con tecnología Z-Wave.

Es necesario disponer de una Unidad de Control Z-Wave para poderlo integrar y controlar desde su red Z-Wave. Este módulo Z-Wave funciona como si fuera un repetidor sin cables con los demas dispositivos para favorecer el mallado de la red Z-Wave y aumentar cobertura en las estancias.

FUNCIONES :

Controlar a distancia un aparato o grupo de aparatos conectados a circuitos de fuerza
Función ON/OFF
Medición del consumo instantáneo y acumulado.
Funciona para cargas de hasta 40 amperios maximo
Fabricación basada en la gama Gen5 de Aeon Labs
Seguridad de la comunicacion vía radio mediante cifrado AES-128
Integra la tecnología Z-Wave de la serie 500
Comunicacion 250% más rapida comparada a dispositivos Z-Wave standard
Suporta las tramas d e exploracion Z-Wave
Soporta Beaming
Actualizaciones de firmware de forma inalámbrica: Over The Air (OTA)
Repetidor de mensajes Z-Wave
Optimizacion de alcance de la antena hasta 150 metros
Facilidad de utilización y de instalación

CARACTERISTICAS TECNICAS :

Tipo de modulo: Receptor Z-Wave (Z-Wave Plus)
Alimentacion: 240VAC, 50/60Hz
Consumo: 1W
Carga maxima: 9600W / 40A
Frequencia : 868,42 Mhz
Distancia de transmision: 200 m en campo abierto
Protección IP: IP43
Dimensiones: 150mm x 118mm x 35mm
Peso: 350g
Temperatura de funcionamiento: 5-40°C
Humedad soportadapara funcionamiento: 80%
Certificaciones: FCC, UL, CE, ROHS

Fibaro HC Lite compatible Sí
Fibaro HC2 compatible Sí
Vera 3/Lite compatible Sí
ZIPABOX compatible Sí
eedomus compatible Sí
Domoticz compatible Sí

Información Ampliada Z-Wave (Inglés)

Nombre: Heavy Duty Smart Switch Gen5

Fabricante:Aeotec

Identificador:ZW078-C

Número de Certificación Z-Wave:ZC10-14090016

Plataforma Hardware:ZM5202

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:Heavy Duty Smart Switch Gen5 is an on/off switch module that also provides energy metering.

Descripción:Aeon Labs Heavy Duty Smart Switch is a Z-Wave device that can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway), it can be controlled by other Z-Wave devices to turn on/off loads, it can bear up to 40A current of resister loads. It also acts as a repeater that forward Z-Wave command messages to destination nodes if the originating controller is out of range from the destination node. By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary “listening” Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate. When the switch is turned on or off using the action button, the switch will send a basic report of its status to the nodes in association group 1. To change what kind of signal is sent to the nodes in group 1, please see the detailed description of configuration parameter 80.

2

5

When the product receives a controlling Basic Set CC/Switch Binary Set CC/ Scene Activation Set CC, which if cause the product’s load state to be changed, which will lead to send the Basic Set CC/Switch Binary Set CC /Scene Activation Set CC to nodes in group 2.

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

101

4

To set which report need to be sent.

This parameter is used to configure which reports need to be sent in Report Group 1. The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 101 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported. See the full description of the parameter values for other possible settings.

102

4

8

To set which report need to be sent.

This parameter is used to configure which reports need to be sent in Report Group 2. The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 102 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported. See the full description of the parameter values for other possible settings.

103

4

0

To set which report need to be sent.

This parameter is used to configure which reports need to be sent in Report Group 3. The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 103 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported. See the full description of the parameter values for other possible settings.

111

4

300

Set the interval time of sending report.

This parameter is used to set the interval time of sending report in Report Group 1. (The unit of time is second).

112

4

120

Set the interval time of sending report.

This parameter is used to set the interval time of sending report in Report Group 2. (The unit of time is second).

113

4

120

Set the interval time of sending report.

This parameter is used to set the interval time of sending report in Report Group 3. (The unit of time is second).

20

1

0

The load status after power on

This parameter is used for indicating the state of output load after re-power on.

200

1

0

Partner ID

This parameter is used to configure the partner ID. (0== Aeon Labs Standard Product, 1~255== others).

252

1

0

Enable/Disable Lock Configuration

This parameter is used to enable/disable Lock all configuration parameters. (0 =disable, 1 = enable)

255

4

0

Reset to default factory setting

This parameter is used to reset product to default factory setting. (There are just 2 values can be used).

3

1

0

Current Overload Protection

This parameter is used for the overload protection, which means the load will be disconnected after 5 seconds when the current more than 39.5A.

80

1

0

Enable/Disable to send notifications to associated devices to associated devices.

This parameter is used to Enable/Disable to send notifications to associated devices (in Group 1) when the state of Smart Switch Gen5’s load is changed. (0=Send nothing, 1=Send hail CC, 2=Send basic report CC).

90

1

Enable/Disable the function of parameter 91 and 92.

This parameter is used to Enable/Disable the function of parameter 91 and 92 (1=Enabled, 0=Disabled).

91

2

50

Induce an automatic report

This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in wattage.

92

1

10

Induce an automatic report

This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in percentage.

Basic

COMMAND_CLASS_BASIC

Hail

COMMAND_CLASS_HAIL

Scene Activation

COMMAND_CLASS_SCENE_ACTIVATION

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Inclusion

Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing.

Exclusion

Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing.

Learn Mode (adding another controller)

N/A

Factory Reset

Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.

Device Wake-Up

N/A

Additional Special Features

Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.