fibaro dimmer 2 FGD-212 regulador universal 250w z-wave plus

Características técnicas

Tecnología	Z-Wave Plus
Característica	Dimmer

Descripción

El micromódulo "dimmable" o regulador de Fibaro FGD-212 es un dimmer o regulador para alumbrado que permite conservar el actual interruptor instalado al introducirse en su misma caja de mecanismo. Puede actuar para apagar o encender la lampara conectada como carga, así como hacer variar su intensidad utilizando su actual interruptor, mediante un controlador doótico Z-Wave o directamente a través del boton del propio micromódulo.

El nuevo dimmer de Fibaro FGD-212 dispone de un algoritmo de detección inteligente de la fuente o carga de iluminación que facilita la configuración y asegura una alta compatibilidad del tipo de lámpara a controlar. Dispone de una autoprotección contra la sobrecarga y de la función de encendido suave y progresivo. En el caso de fuentes luminosas no "dimmables", esto es, no graduables, sólo ofrecerá como disponible la función on/off (apagar o encender) usando 3 cables.

El micromódulo Dimmer 2 de Fibaro es compatible con todo tipo de lámparas ya soporten regulación o no:

Modo regulador:

- Fuentes de alumbrado clasicas incandescentes y halogenas alimentadas a 230 VAC
- Lamparas halogenas 12V (con transformadores electronicos)
- Lamparas halogenas 12V (con transformadores ferromagnéticos)
- Lamparas LED variables (dimmables)
- Lamparas CFL fluorescentes variables (dimmables)
- Utilizacion de Bypass de Fibaro con una fuente de alumbrado de intensidad regulable 225VA hasta 2 hilos (dependiendo del tipo de carga)

Modo interruptor:

- Lamparas fluorescentes
- Lamparas LED
- Utilización de Bypass Fibaro con toda fuente de alumbrado compatible j225VA (en funcion del tipo de carga)

Se puede utilizar en el modo 2 hilos (sin neutro), para la sustitución de un interruptor existente, o tres hilos con un módulo de potencia convencional (fase + neutro). Para lámparas con un consumo de energía muy bajo (lámpara LED, por ejemplo), puede utilizar la carga (bypass) FGB-001 que permite un funcionamiento correcto del modulo.

Además de la función de regulación, este micro-módulo de Fibaro también puede medir el consumo de energía de la carga conectada. Las cifras de consumo instantáneo (en W) y el consumo total de electricidad (kWh) pueden ser monitorizados y consultados.

Es necesario integrar el micromódulo en su red Z-Wave a través de un controlador domótico Z-Wave.

Cada módulo Z-Wave funciona como un repetidor inalámbrico con otros módulos para garantizar una cobertura total de la red Z-Wave de su hogar o su oficina.

Presentación PDF Fibaro Dimmer 2 (en inglés)

FUNCIONES :

Controlar el alumbrado a distancia
Se puede instalar detrás de un interruptor ya existente
Funcion ON/OFF y dimmer (regulacion de intensidad lumínica)
Utilizacion en modo 2 hilos (neutro no es necesario)
Integre la tecnología Z-Wave serie 500: Z-Wave Plus GEN5
Communicacion 250% más rapida comparada a los periféricos Z-Wave standard
Detección automatica de la carga
Protección contra sobrecargas
Compatible con todos los controladores domóticos Z-Wave y Z-Wave Plus
Función de medición de consumo electrico
Funciona con diferentes tipos de interruptores - pulsador, basculante, de tres vías, etc.
Función de arranque progresivo (Soft-start)
Diodo LED de indicación del estado de la inclusión, niveles de menú y calibración
Probador de alcance Z-Wave integrado
Detecta automáticamente los defectos en el cable, temperatura elevada, Détecte automatiquement les défauts de câblage, température élevée, bulbo, sobretensiones y sobrecargas
Opciones de configuracion avanzada
Pequeño, discreto y estético
Facilidad de utilización y de instalación

CARACTERÍSTICAS TÉCNICAS :

Tipo de modulo: Receptor Z-Wave
Alimentación: 230V +/- 10%, 50Hz
Consumo: 1.3W
Cableado: neutro no necesario
Carga máxima: 50-250W (carga resistiva) o 0.25-1.1A (carga inductiva)
Tipo de lampara compatible ("dimmable"): Incandescente, Fluocompacta, Halogena (230VAC y 12VDC con transformador electrónico), LED
Tipo de lampara compatible ("no dimmable"): Fluocompacta, LED
Frequencia: 868,42 Mhz
Intensidad de señal: 1mW
Distancia de transmisión: 50m en campo abierto, 30m en interiores
Dimensiones: 42.5 x 38.25 x 20.3 mm
Temperatura de funcionamiento: 0-35°C
Temperatura límite: 105°C
Normas y certificaciones: RoHS 2011/65/EU, LVD 2006/95/EC, EMC 2004/108/EC, R&TTE 1999/5/EC

Descargar

Fibaro Dimmer 2

Manual del Dimmer 2 de Fibaro

Descargar (632.17k)

Información Ampliada Z-Wave (Inglés)

Nombre: FIBARO Dimmer 2

Fabricante:FIBARO

Identificador:FGD-212

Número de Certificación Z-Wave:ZC10-18026008

Plataforma Hardware:ZM5202

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:Remotely controlled light dimming module is designed to work with various types of light sources in 2 or 3-wire connection so it can operate with or without neutral lead.

Descripción:FIBARO Dimmer 2 can switch or dim connected light source either through radio waves or through the wall switch connected directly to it. Dimmer 2 is equipped with a smart algorithm of light source detection which makes configuration easier and ensures high compatibility of the device. It may be used as a switch with non-dimmable light sources in 3-wire connection. Active power and energy consumption allows to monitor and reduce electricity bills. Dimmer 2 is compatible with any Z-Wave or Z-Wave Plus Controller. FIBARO Dimmer 2 Product Identifier: FGD-212 Brand Name: FIBARO Z-Wave Certification Number: ZC10-15090017 Z-Wave Certification Date: 9/16/2015 Z-Wave Protocol Implementation Conformance Statement: View Download Remotely controlled light dimming module is designed to work with various types of light sources in 2 or 3-wire connection so it can operate with or without neutral lead. FIBARO Dimmer can switch or dim connected light source either through radio waves or through the wall switch connected directly to it. Dimmer 2 is equipped with a smart algorithm of light source detection which makes configuration easier and ensures high compatibility of the device. It may be used as a switch with non-dimmable light sources in 3-wire connection. Active power and energy consumption allows to monitor and reduce electricity bills. Dimmer 2 is compatible with any Z-Wave or Z-Wave Plus Controller. As a dimmer it operates under the following loads: • 230V operated conventional incandescent and halogen light sources • ELV electronic transformers (12V operated halogen lamps and dimmable LED bulbs) • MLV ferromagnetic transformers with 12V operated halogen lamps • dimmable LED bulbs • dimmable compact fluorescent CFL tube lamps • supported dimmable light sources with minimal power of 5VA (power factor > 0.5) using FIBARO Bypass FGB-002 Without dimming function it may work with: • compact fluorescent lamps • fluorescent tube lamps with electronic ballast • LED bulbs (power factor > 0.7) • supported light sources with minimal power of 5VA (power factor > 0.5) using FIBARO Bypass FGB-002 https://www.youtube.com/watch?v=K35uFXoa5c0

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

Z-Wave Plus Lifeline. Type of frame sent by the device when the association group is activated: SWITCH_MULTILEVEL_REPORT; DEVICE_RESET_LOCALLY_NOTIFICATION; SCENE_ACTIVATION_SET; METER_REPORT; SENSOR_MULTILEVEL_REPORT; NOTIFICATION REPORT.

2

8

Association Group „On/Off (S1)” is assigned to key no. 1. Type of frame sent by the device when the association group is activated: BASIC_SET.

3

8

Association Group „Dimmer (S1)” is assigned to key no. 1. Type of frame sent by the device when the association group is activated: SWITCH_MULTILEVEL_SET.

4

8

Association Group „On/Off (S2)” is assigned to key no. 2. Type of frame sent by the device when the association group is activated: BASIC_SET.

5

8

Association Group „Dimmer (S2)” is assigned to key no. 2. Type of frame sent by the device when the association group is activated:SWITCH_MULTILEVEL_SET.

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

1

Minimum brightness level

The parameter can be changed manually after the calibration. 1-98 - percentage level of brightness CAUTION The maximum brightness level (parameter 2) must be greater than the minimum brightness level (parameter 1).

10

2

0

Timer functionality (auto - off)

This parameter allows to automatically switch off the device after specified time from switching on the light source. It may be useful when the Dimmer 2 is installed in the stairway.

11

2

255

ALL ON/ALL OFF function

Parameter allows for activation/deactivation of Z-Wave commands enabling/disabling all devices located in direct range of the main controller.

13

1

0

Force auto-calibration

Changing value of this parameter will force the calibration process. During the calibration parameter is set to 1 or 2 and switched to 0 upon completion.

14

1

0

Auto-calibration status

This parameter determines operating mode of the Dimmer 2 (automatic/ manual settings).

15

1

30

Burnt out bulb detection

Function based on the sudden power variation of a specific value, interpreted as a LOAD ERROR. CAUTION Parameter 15 is relevant only when parameter 58 is set to 0 and the control mode is consistent with the mode set during the calibration process (parameter 30).

16

2

5

Time delay of a burnt out bulb (parameter 15) or overload (parameter 39) detection

Time of delay (in seconds) for power variation detection, interpreted as a LOAD ERROR or OVERLOAD detection (too much power connected to the Dimmer 2).

19

1

0

Forced switch on brightness level

If the parameter is active, switching on the Dimmer 2 (S1 single click) will always set this brightness level.

2

1

99

Maximum brightness level

The parameter can be changed manually after the calibration 2-99 - percentage level of brightness

20

1

0

Switch type

Choose between momentary, toggle and roller blind switch.

21

1

0

The value sent to associated devices on single click

This parameter defines the value sent to devices associated with Dimmer 2 after its enabling.

22

1

0

Assign bistable key status to the device status

By default each change of toggle switch position results in action of Dimmer 2 (switch on/off) regardless the physical connection of conntacts.

23

1

Double click option

set the brightness level to MAX

24

1

0

Command frames sent in 2-nd and 3-rd association groups (S1 associations)

Parameter determines, which actions will not result in sending frames to association groups. Parameter 24 values may be combined, e.g. 1+2=3 means that associations on switching ON or OFF the Dimmer 2 (single click) will not be sent.

25

1

0

Command frames sent in 4-th and 5-th association groups (S2 associations)

Parameter determines, which actions will not result in sending frames to association groups. Parameter 25 values may be combined, e.g. 1+2=3 means that associations on switching ON or OFF the Dimmer 2 (single click) will not be sent.

26

1

0

The function of 3-way switch

Switch no. 2 controls the Dimmer 2 additionally (in 3-way switch mode). Function disabled for parameter 20 set to 2 (roller blind switch).

27

1

15

Associations in Z-Wave network security mode

This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st Lifeline group. NOTE Parameter 27 values may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure.

28

1

0

Scene activation functionality

SCENE ID depends on the switch type configurations. NOTE Enabling scene activation functionality may cause slight delay in response to external switches and sending associations.

29

1

0

Switch functionality of S1 and S2

This parameter allows for switching the role of keys connected to S1 and S2 without changes in connection

3

1

Incandescence level of dimmable compact fluorescent lamps

Virtual value set as a percentage level between parameters MIN (1%) and MAX. (99%). The Dimmer 2 will set to this value after first switch on. It is required for warming up and switching dimmable compact fluorescent lamps and certain types of light sources. 1-99 - percentage level of brightness

30

1

2

Load control mode

This parameter allows to set the desired load control mode. The device automatically adjusts correct control mode, but the installer may force its change using this parameter. Forced auto-calibration will set this parameter’s value to 2. CAUTION Modifications of parameters in GROUP 30 should be performed only by a qualified installer.

31

1

0

Load control mode recognized during auto-calibration

Load control mode recognized during auto-calibration (read only)

32

1

2

On/Off mode

This mode is necessary while connecting non-dimmable light sources. Setting this parameter to 1 automatically ignores brightening/ dimming time settings. Forced auto-calibration will set this parameter’s value to 2.

33

1

0

Dimmability of the load

This parameter contains an information about possibility of dimming the load detected during calibration procedure.

34

1

Soft-Start functionality

Time required to warm up the filament of halogen bulb.

35

1

Auto-calibration after power on

This parameter determines the trigger of auto-calibration procedure, e.g. power on, load error, etc.

37

1

Behaviour of the Dimmer after overload or surge.

Occuring of errors related to surge or overcurrent results in turning off the output to prevent possible malfunction. By default the device performs three attempts to turn on the load (useful in case of momentary, short failures of the power supply).

38

2

255

Brightness level correction for flickering loads

Correction reduces spontaneous flickering of some capacitive load (e.g. dimmable LEDs) at certain brightness levels in 2-wire installation. In countries using ripple-control, correction may cause changes in brightness. In this case it is necessary to disable correction or adjust time of correction for flickering loads.

39

2

250

Power limit - OVERLOAD

Reaching the defined value will result in turning off the load. Additional apparent power limit of 350VA is active by default.

4

2

0

Incandescence time of dimmable compact fluorescent lamps

This parameter determines the time required for switching compact fluorescent lamps and certain types of light sources. Setting this parameter to 0 will disable the incandescence functionality. 0s - 25,5s

40

1

3

Response to General Purpose Alarm

41

1

2

Response to Water Flooding Alarm

42

1

3

Response to Smoke, CO or CO2 Alarm

43

1

Response to Temperature Alarm

44

2

600

Time of alarm state

Time of alarm state. NOTE: Alarm state may be cancelled earlier, as a result of pressing the switch or ending the Z-Wave command frame.

45

1

OVERLOAD alarm report

OVERLOAD alarm report (load power consumption too high)

46

1

LOAD ERROR alarm report

LOAD ERROR alarm report (no load, load failure, burnt out bulb)

47

1

OVERCURRENT alarm report

OVERCURRENT alarm report (short circuit, burnt out bulb causing overcurrent)

48

1

SURGE alarm report

SURGE alarm report (Dimmer 2 output overvoltage)

49

1

OVERHEAT and VOLTAGE DROP alarm report

OVERHEAT (critical temperature) and VOLTAGE DROP (low voltage) alarm report

5

1

Automatic control - dimming step size

dimming step percentage value

50

1

10

Active power reports

The parameter defines the power level change that will result in a new power report being sent. The value is a percentage of the previous report. 0 - power reports disabled 1-100 (1-100%) - power report threshold

52

2

3600

Periodic active power and energy reports

Parameter 52 defines a time period between consecutive reports. Timer is reset and counted from zero after each report. 0 - periodic reports disabled 1-32767 (1-32767 seconds)

53

2

10

Energy reports

Energy level change which will result in sending a new energy report. 0 - energy reports disabled 1-255 (0.01-2.55 kWh) - report triggering threshold

54

1

0

Self-measurement

The Dimmer 2 may include active power and energy consumed by itself in reports sent to the main controller.

58

1

0

Method of calculating the active power

This parameter defines how to calculate active power. It is useful in a case of 2-wire connection with light sources other than resistive. NOTE Parameter 58 is set to 0 after forced auto-calibration.

59

2

0

Approximated power at the maximum brightness level

This parameter determines the approximate value of the power that will be reported by the device at its maximum brightness level. 0-500 (0-500W) - power consumed by the load at the maximum brightness level. NOTE Parameter 59 works only when parameter 58 has a value other than 0.

6

2

1

Automatic control - time of a dimming step

This parameter defines the time of single dimming step set in parameter 5 during the automatic control.

7

1

Manual control - dimming step size

This parameter defines the percentage value of dimming step during the manual control.

8

2

5

Manual control - time of a dimming step

This parameter defines the time of single dimming step set in parameter 7 during the manual control.

Basic

COMMAND_CLASS_BASIC

Scene Activation

COMMAND_CLASS_SCENE_ACTIVATION

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Configuration

COMMAND_CLASS_CONFIGURATION

CRC16 Encapsulation

COMMAND_CLASS_CRC_16_ENCAP

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V3

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Notification V5

COMMAND_CLASS_NOTIFICATION_V5

Powerlevel

COMMAND_CLASS_POWERLEVEL

Protection V2

COMMAND_CLASS_PROTECTION_V2

Security S0

COMMAND_CLASS_SECURITY

Sensor Multilevel V4

COMMAND_CLASS_SENSOR_MULTILEVEL_V4

Switch All

COMMAND_CLASS_SWITCH_ALL

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Exclusion

1) Set the main controller in remove mode (see the controller’s manual)

2) Quickly, three times press the B-button or key connected to the S1 terminal.

3) Wait for the device to be removed from the system. Successful removing will be confirmed by the controller.

Inclusion

1) Switch off the mains voltage.

2) Open the wall switch box.

3) Connect the Dimmer in accordance with one of the diagrams attached in the manual.

4) Switch on the mains voltage.

5) Wait for the calibration process to end. Light may blink. The device will be switched off once the process is completed.

6) Set the main Z-Wave controller in add mode (see the controller’s manual).

7) Quickly, three times press the B-button or key connected to the S1 terminal.

8) Wait for the device to be added to system. Successful adding will be confirmed by the controller.

9) Arrange the antenna and close the wall switch box.

Device Wake-Up

The FIBARO Dimmer 2 is powered with mains voltage so it is always awake.

Additional Special Features

Active power and metering functionality

Soft start function

Memory of the last lighting level settings

Z-Wave range tester

LED diode

Factory Reset

1) Disconnect the power supply, remove the Dimmer from the wall switch box, than connect the power supply.

2) Locate the B-button on the housing.

3) Click and hold the B-button to enter the menu mode.

4) Release and click the B-button to choose ""Device reset"" option in the menu that is signalled with the yellow LED indicator colour.

5) After few seconds the device will be restarted, which is signalled with the red LED indicator colour and entering the calibration mode.

Note! Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable.

Switch Load Capacity Current

The amount of switch load energy the product is rated for in Amps

Supported Meter Type

Indicate which type of metering is supported by the device.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).

Color

If the product is only available in one color, pick the color from the list.

Sensors

Sensor types supported by the product.