Shelly Qubino Wave PRO 1 - módulo de carril DIN de 1 relé de contacto seco Z-Wave 800

Características técnicas

Tecnología Domótica	Z-Wave Serie 800

Descripción

Wave Pro 1 es un interruptor inteligente monofásico de 1 canal para montaje en carril DIN que admite hasta 16 A para la automatización de iluminación profesional y electrodomésticos de uso residencial o comercial. Está equipado con una salida libre de potencial (contactos secos) que ofrece una gran flexibilidad en términos de tensión y aplicaciones. Se pueden definir diferentes tipos de acciones, escenarios y horarios para sincronizar su entorno con sus actividades diarias o necesidades empresariales.

Shelly Qubino funciona con Z-Wave

Gracias a Z-Wave, los productos domóticos se comunican perfectamente entre sí, independientemente de la marca o la plataforma, gracias a una pasarela inteligente centralizada. Los dispositivos Shelly Qubino funcionan con la última generación de chips Z-Wave (S800), una de las tecnologías estandarizadas más populares para hogares inteligentes en todo el mundo.

Funciona con cualquier pasarela Z-Wave

Wave Pro 1 es compatible con versiones anteriores y está diseñado para encajar detrás de interruptores/pulsadores. Una vez instalado, incluya el dispositivo en su red Z-Wave (se requiere una pasarela Z-Wave) y contrólelo utilizando su smartphone o tableta. Los dispositivos Shelly Qubino funcionan con más de 4000 dispositivos y pasarelas certificados Z-Wave.

1 canal, 16 A

Tiene una salida total de 16 A.

Contactos secos

Admite tensiones bajas y altas, lo que le permite controlar una amplia gama de dispositivos y electrodomésticos de CA.

Montaje en carril DIN

Previsto para su instalación en el interior de la caja del disyuntor y diseñado para cumplir la normalización mundial de carril DIN.

Asociaciones

Establezca una comunicación directa entre los dispositivos de su red Z-Wave local y defina acciones sin necesidad de una pasarela.

El más alto nivel de seguridad

Incluya el dispositivo como Security 2 Authenticated para una comunicación encriptada y la máxima seguridad de su red Z-Wave.

FUNCIONES del Shelly Wave Pro 1

1 salida, 16 A
Contactos libres de potencial (contactos secos)
Montaje en carril DIN
Consumo de energía extremadamente bajo: < 0,3 W
Banda de frecuencia Z-Wave: 868,4 MHz (países CEPT)
Última tecnología: serie Z-Wave 800
Configuración automática con SmartStart
Seguridad 2 autenticada para el máximo nivel de seguridad
Actualizaciones de firmware vía radio
Funciona con pasarelas Z-Wave certificadas y más de 4000 dispositivos Z-Wave

ESPECIFICACIONES TÉCNICAS del Shelly Wave Pro 1

Alimentación: 110-240 V AC, 50/60 Hz
Consumo de energía: < 0,3 W
Tensión máxima de conmutación de CA: 240 V
Corriente de conmutación de CA máxima: 16 A
Protección contra sobrecalentamiento: Sí
Distancia: Hasta 40 m en interiores (dependiendo de las condiciones locales)
Repetición Z-Wave: Sí
Procesador: Z-Wave S800
Bandas de frecuencia Z-Wave: 868,4 MHz
Potencia máxima de radiofrecuencia emitida en la(s) banda(s) de frecuencia: < 25 mW
Dimensiones (Al x An x Pr): 94x19x69 ±0,5 mm
Peso: 60 g
Montaje: carril DIN
Par máximo de apriete de los bornes: 0,4 Nm
Sección del conductor: 0,5 a 2,5 mm / 20 a 14 AWG (conector verde) 0,5 a 1,5 mm / 20 a 16 AWG (conectores blancos)
Longitud de pelado del conductor: 6 a 7 mm (conector verde) 5 a 6 mm (conectores blancos)
Material de la carcasa: Plástico
Color: Azul
Temperatura ambiente : -20°C a 40°C
Humedad: 30% a 70% HR

Información Ampliada Z-Wave (Inglés)

Nombre: Wave Pro 1

Fabricante:Shelly Qubino

Identificador:QPSW-0A1X16EU

Número de Certificación Z-Wave:ZC14-24010391

Plataforma Hardware:EFR32ZG23A

FLiRS:NO

Tipo de Role:Always On End Node

Descripción Corta:Wave Pro 1 controls the on/off function for one electrical device (with load up to 16A), e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. The output contact is potential-free (dry contact).

Descripción:Wave Pro 1 controls the on/off function for one electrical device (with load up to 16A), e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. The output contact is potential-free (dry contact).

Grupo

Max Nodos

Descripción

1

9

2

9

3

9

4

9

5

9

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

1

2

SW1 Switch type

0 push, 1 toggle state, 2 toggle change

120

1

0

Factory reset

17

1

0

Restore state of O1 after power failure

0 restore, 1 no restore

19

2

0

Turn O1 OFF Automatically with timer

1 - 32535, 0 disabled

2

1

2

SW2 Switch type

0 push, 1 toggle state, 2 toggle change

20

2

0

Turn O1 ON Automatically with timer

1 - 32535, 0 disabled

201

4

2147483647

Serial Number 1

202

4

2147483647

Serial Number 2

203

4

2147483647

Serial Number 3

23

1

0

O1 NO/NC

0 NO, 1 NC

25

1

0

Set timer units to Seconds or Milliseconds for O1

0 seconds, 1 milliseconds

91

4

0

Alarm conf. - Water

0 no action 1 open relay 2 close relay

92

4

0

Alarm conf. - Smoke

0 no action 1 open relay 2 close relay

93

4

0

Alarm conf. - CO

0 no action 1 open relay 2 close relay

94

4

0

Alarm conf. - Heat

0 no action 1 open relay 2 close relay

Association Group Information (AGI) V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Binary Switch V2

COMMAND_CLASS_SWITCH_BINARY_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security 0

COMMAND_CLASS_SECURITY

Security 2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

When adding the Device to a Z-Wave network with a gateway supporting Security 2 (S2), the PIN Code of the Z-Wave Device Specific Key (DSK) is required. You can find it on the label on the side of the Device and a copy is inserted in the packaging, which must not be lost. Do not remove the Z-Wave DSK label from the Device. As a backup measure, use the label in the packaging.

The first five digits of the key are highlighted or underlined to help the user identify the PIN Code part of the DSK text. The DSK is additionally represented with a QR Code as shown on the image.

Classic Inclusion

6.1 Adding the Device to a Z-Wave® network (inclusion)

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave® network.

Note! In case of Security 2 (S2) adding (inclusion), a dialog will appear asking you to enter the corresponding PIN Code (5 underlined digits) that are written on the Z-Wave® DSK label on the side of the Device and on the Z-Wave® DSK label inserted in the packaging.

IMPORTANT: The PIN Code must not be lost.

6.1.1 SmartStart adding (inclusion)

SmartStart enabled products can be added into a Z-Wave® network by scanning the Z-Wave® QR Code present on the Device with a gateway providing SmartStart inclusion. No further action is required, and the SmartStart device will be added automatically within 10 minutes of being switched on in the network vicinity.

1. With the gateway application scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list in the gateway.

2. Connect the Device to a power supply.

3. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network.

4. Adding will be initiated automatically within a few seconds after connecting the Device to a power supply, and the Device will be added to a Z-Wave® network automatically.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network.

6.1.2 Adding (inclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the adding process.

7. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

6.1.3 Adding (inclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2, etc.) 3 times within 3 seconds (this procedure puts the Device in Learn mode*). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the adding process.

6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network.

*Learn mode - a state that allows the Device to receive network information from the gateway.

Classic Exclusion

6.2 Removing the Device from a Z-Wave® network (exclusion)

Note! The Device will be removed from your Z-Wave® network, but any custom configuration parameters will not be erased.

Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave® network.

6.2.1 Removing (exclusion) with the S button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave® network.

3. Enable add/remove mode on the gateway.

4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.

6. The blue LED will be blinking in Mode 2 during the removing process.

7. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave® network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

6.2.2 Removing (exclusion) with a switch/push-button

1. Connect the Device to a power supply.

2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave® network.

3. Enable add/remove mode on the gateway.

4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.

5. The blue LED will be blinking in Mode 2 during the removing process.

6. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave® network.

Factory Reset Procedure

6.3 Factory reset

6.3.1 Factory reset general

After Factory reset, all custom parameters and stored values (kWh, associations, routings, etc.) will return to their default state. HOME ID and NODE ID assigned to the Device will be deleted. Use this reset procedure only when the gateway is missing or otherwise inoperable.

6.3.2 Factory reset with the S button

Note! Factory reset with the S button is possible anytime.

1. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.

2. Press the S button multiple times until the LED turns solid red.

3. Press and hold (> 2s) S button on the Device until the red LED starts blinking in Mode 3. Releasing the S button will start the factory reset.

4. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 5 for approx. 2s.

5. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.3 Factory reset with a switch/push-button

Note! Factory reset with a switch/push-button is only possible within the first minute after the Device is connected to a power supply.

1. Connect the Device to a power supply.

2. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 5 times within 3 seconds. The Device must receive on/off signal 5 times, which means pressing the push-button 5 times, or toggling the switch on and off 5 times.

3. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 5 for approx. 2s.

4. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

6.3.4 Remote factory reset with parameter

Factory reset can be done remotely with the settings in Parameter No. 120.

1. Set par.120 to value 1 - Do the Factory reset

2. During factory reset, the blue and red LED will start blinking in Mode 5 for approx. 2s.

3. The blue LED will be blinking in Mode 1 if the Factory reset is successful.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Color

If the product is only available in one color, pick the color from the list.

Electric Load Type

Select the electric load type(s) supported by the device.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.