Características técnicas

Tecnología Domótica	Z-Wave Plus

Descripción

El MultiSensor6 es un detector Z-Wave de ultima generación (GEN5), dispone de 6 funciones y cuenta con el nuevo chip Z-Wave de la serie 500, el cual ofrece menor consumo, mayor potencia y mayor alcance de la red Z-Wave.

MultiSensor 6 no sólo ha dispuesto de un rediseño del sensor más inteligente de AEOTEC, sino que ha sido somtido a una profunda re-ingeniería desde dentro hacia fuera.

Pasamos a describir sus 6 interesantes funciones:

Detector de movimiento

Con una distancia de 5 metros y un campo de visión de 120°, MultiSensor 6 de AEOTEC obtiene datos sobre el movimiento que pueden ser utilizados tanto para seguridad como para la gestión de la calefacción, entre otras aplicaciones.

Sensor de temperatura

MultiSensor 6 integra una temperatura sensor puede medir la temperatura de -10 a + 50 ° C con precisión .

Sensor de luz

Con multidetector 6 en puede medir el nivel de luz en una habitación, le ayudará a crear escenas en base al nivel de luz, subir o bajar persianas etc..

Aeotec Multisensor 6 - sensor luminosidad z-wave

Sensor de humedad

MultiSensor 6 ofrece seguimiento incremental de una humedad que van desde 0% a 100%, lo que permite la automatización inteligente de ventiladores, ventanas motorizadas, deshumidificadores y humidificadores

Sensor de vibración.

MultiSensor 6 contiene un sensor sísmico capaz de detectar y reportar las vibraciones. Esos ligeros cambios pueden ser utilizados para proteger el MultiSensor 6, sabrá si un intruso lo está manipulando o si accidentalmente el sensor se ha movido de su lugar de instalación. También podrá registrar actividad sísmica sutil dentro de su hogar

Sensor de rayos UV

MultiSensor 6 mide con precisión la luz ultravioleta, conociendo este dato, podremos poner medidas para que los valores no sean altos y puedan afectar tanto a la salud de las personas como al deterioro de muebles u otro tipo de cosas que tengamos expuestos.

Aeotec Multisensor 6 - sensor ultravioleta

Aeotec Multisensor 6 - No sólo pequeño. Perfectamente pequeño.

La creación de un objeto diseñado para asegurar y administrar su hogar requiere de precisión. También requiere sutileza. El MultiSensor 6 es perfectamente pequeño. Es bellamente cónico, su cuerpo de 42 mm permite que sea usado en cualquier lugar de la casa, pero su diseño y estilo no son sólo para la apariencia. Una base cuadrada permite que el MultiSensor 6 ofrezca más de 2 años de vida de la batería, lo mejor de cualquier sensor de movimiento de Onda Z. Aeon Labs introdujo el estilo de cámara de seguridad en el MultiSensor 6. Y como vivimos en una era de privacidad, el MultiSensor 6 ofrece un sutil LED con la opción de informar con un arco iris de colores o apagarlo completamente.

El MultiSensor 6 ha sido diseñado para ser más que bello; ha sido diseñado para que su presencia en una habitación nunca sea obvia. Lo sutil es inteligente.

Aeotec Multisensor 6 - tamaño

Información Ampliada Z-Wave (Inglés)

Nombre: TriSensor

Fabricante:Aeotec

Identificador:ZWA005-C

Número de Certificación Z-Wave:ZC10-18046087

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Reporting Sleeping Slave

Descripción Corta:Aeotec TriSensor has a motion detector, ambient temperature and ambient light sensor in one, based on Z-Wave Plus technology.

Descripción:TriSensor can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. If PIR motion sensor is triggered, the TriSensor will send a Basic set to associated devices. The PIR motion sensor will then become inactive. If no PIR motion is triggered after the PIR interval time (configurable), the TriSensor will send Basic Set to the associated nodes.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Group 1 is lifeline group; all nodes which associated in this group will receive the messages sent by device through lifeline. Command Class: COMMAND_CLASS_NOTIFICATION COMMAND_CLASS_SENSOR_BINARY COMMAND_CLASS_SENSOR_MULTILEVEL COMMAND_CLASS_BATTERY COMMAND_CLASS_DEVICE_RESET_LOCALLY Command : NOTIFICATION_REPORT SENSOR_BINARY_REPORT SENSOR_MULTILEVEL_REPORT BATTERY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION

2

5

Group 2 is controlling group, all nodes associated in this group will be controlled through BASIC_SET command by the device when device detects a movement event. Basic Set Value is decided by Configuration Parameter 6. Command Class: COMMAND_CLASS_BASIC (Home Security) Command : BASIC_SET

3

5

Group 3 is controlling group, all nodes associated in this group will be controlled through BASIC_SET command by the device when device detects an ambient temperature alarm (Decided by Configuration Parameter 7). Command Class: COMMAND_CLASS_BASIC (Temperature) Command : BASIC_SET

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

1

2

30

Motion Retrigger Time

This parameter is configured the delay time before PIR sensor can be triggered again to reset motion timeout counter. Value = 0 will disable PIR sensor from triggering until motion timeout has finished.

10

1

Led Indicate Disable

This parameter is configured the Led light on disable or enable. ‘1’ – Enable Led Blink when device detects a motion event. ‘0’ – Disable Led Blink. This configuration is not affect inclusion, exclusion and reset.

100

2

1024

Light Sensor Calibrated Coefficient

This configuration defines the calibrated scale for ambient light intensity. Because the method and position that the sensor mounted and the cover of sensor will bring measurement error, user can get more real light intensity by this parameter setting. User should run the steps as blows for calibrating 1) Set this parameter value to default (Assumes the sensor has been added in a Z-Wave Network). 2) Place a digital luxmeter close to sensor and keep the same direction, monitor the light intensity value (Vm) which report to controller and record it. The same time user should record the value (Vs) of luxmeter. 3) The scale calibration formula: k = Vm / Vs. 4) The value of k is then multiplied by 1024 and rounded to the nearest whole number. 5) Set the value getting in to this parameter, calibrate finished. For example, Vm = 300, Vs = 2600, then k = 2600 / 300 = 8.6667 k = 8.6667 * 1024 = 8874.7 ≈ 8875 The parameter should be set to 8875.

11

1

2

Led Color For Motion Event Report

‘0’ – Disable. ‘1’ – Red. ‘2’ – Green. ‘3’ – Blue. ‘4’ – Yellow. ‘5’ – Pink. ‘6’ – Cyan. ‘7’ – Purple. ‘8’ – Orange.

12

1

0

Led Color For Temperature Sensor Report

‘0’ – Disable. ‘1’ – Red. ‘2’ –Green. ‘3’ – Blue. ‘4’ – Yellow. ‘5’ – Pink. ‘6’ – Cyan. ‘7’ – Purple. ‘8’ – Orange.

13

1

0

Led Color For Light Sensor Report

‘0’ – Disable. ‘1’ – Red. ‘2’ –Green. ‘3’ – Blue. ‘4’ – Yellow. ‘5’ – Pink. ‘6’ – Cyan. ‘7’ – Purple. ‘8’ – Orange.

14

1

0

Led Color For Battery Report

‘0’ – Disable. ‘1’ – Red. ‘2’ –Green. ‘3’ – Blue. ‘4’ – Yellow. ‘5’ – Pink. ‘6’ – Cyan. ‘7’ – Purple. ‘8’ – Orange.

15

1

0

Led Color For Wakeup Notification Report

‘0’ – Disable. ‘1’ – Red. ‘2’ –Green. ‘3’ – Blue. ‘4’ – Yellow. ‘5’ – Pink. ‘6’ – Cyan. ‘7’ – Purple. ‘8’ – Orange.

2

240

Motion Clear Time

This parameter is configured the time to clear motion event after a motion event detected. Time to motion clear, the device will send a clear event report to controller and send BASIC_SET = 0x00 to nodes associated in group 2. Unit: Second.

20

1

0

Temperature Scale Setting

Configure temperature sensor scale type, Temperature to report in Celsius or Fahrenheit. 0 – Celsius (C). 1 – Fahrenheit (F).

21

2

20

Temperature Threshold Value to Report

Change threshold value for change in temperature to induce an automatic report for temperature sensor. Scale is identical setting in Parameter No.20. Setting of value 20 can be a change of -2.0 or +2.0 (C or F depending on Parameter No.20) to induce automatic report or setting a value of 2 will be a change of 0.2(C or F).

22

2

100

Light intensity Threshold Value to Report

Change threshold value for change in light sensor to induce an automatic report for temperature sensor. Scale: Lux.

23

2

3600

Temperature Sensor Report Interval

This parameter is configured the time interval for temperature sensor report. This value is larger, the battery life is longer. And the temperature value changed is not obvious. Unit: Second.

24

2

3600

Light Sensor Report Interval

This parameter is configured the time interval for light sensor report. This value is larger, the battery life is longer. And the light intensity changed is not obvious. Unit: Second.

3

1

11

Motion Sensitivity

This parameter is configured the sensitivity that motion detect. 0 – PIR sensor disabled. 1 – Lowest sensitivity. 11 – Highest sensitivity.

30

2

0

Temperature Offset Value

The current measuring temperature value can be add and minus a value by this setting. The scale can be decided by Parameter Number 20. Temperature Offset Value = [Value] * 0.1(Celsius / Fahrenheit)

31

2

0

Light Intensity Offset Value

The current measuring light intensity value can be add and minus a value by this setting.

4

1

0

Binary Sensor Report Enable

‘0’ –Disable sensor binary report when motion event is detected or cleared. ‘1’ –Enable sensor binary report when motion event is detected or cleared.

5

1

3

Disable BASIC_SET to Associated nodes

This parameter is configured the enabled or disabled send BASIC_SET command to nodes that associated in group 2 and group 3. 0 – Disabled All Group Basic Set Command 1 – Enabled Group 2 Basic Set Command, Group 3 Basic Set Command is disabled. 2 – Enabled Group 3 Basic Set Command, Group 2 Basic Set Command is disabled. 3 – Enabled Group 2 and Group 3 Basic Set Command.

6

1

0

Basic Set Value Settings for Group 2

‘0’ – Send BASIC_SET = 0xFF to devices associated in Group 2 when motion event is triggered, send BASIC_SET = 0x00 to devices associated in group 2 when motion event is cleared. ‘1’– Send BASIC_SET = 0x00 to devices associated in Group 2 when motion event is triggered, send BASIC_SET = 0xFF to devices associated in group 2 when motion event is cleared. ‘2’ – Send BASIC_SET = 0xFF to devices associated in Group 2 when motion event is triggered. ‘3’ – Send BASIC_SET = 0x00 to devices associated in Group 2 when motion event is triggered. ‘4’ – Send BASIC_SET = 0x00 to devices associated in Group 2 when motion event is cleared. ‘5’ – Send BASIC_SET = 0xFF to devices associated in Group 2 when motion event is cleared.

7

2

239

Temperature Alarm Value

This parameter is configured the threshold value that alarm level for temperature. When the current ambient temperature value is larger than this configuration value, device will send a BASIC_SET = 0xFF to nodes associated in group 3. If current temperature value is less than this value, device will send a BASIC_SET = 0x00 to nodes associated in group 3. Value = [Value] × 0.1(Celsius / Fahrenheit)

Basic

COMMAND_CLASS_BASIC

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Battery

COMMAND_CLASS_BATTERY

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Binary V2

COMMAND_CLASS_SENSOR_BINARY_V2

Sensor Multilevel V7

COMMAND_CLASS_SENSOR_MULTILEVEL_V7

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V2

COMMAND_CLASS_VERSION_V2

Wake Up V2

COMMAND_CLASS_WAKE_UP_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Inclusion

Press once TriSensor’s Action Button. If it is the first installation, the yellow LED will keep solid until whole network processing is complete. If successful, the LED will flash white -> green -> white -> green, after 2 seconds finished. If failed, the yellow LED lasts for 30 seconds, then the green LED flashes once.

If it is the S2 encryption network, please enter the first 5 digits of DSK.

Exclusion

Press once TriSensor’s Action Button, the Purple LED will keep solid until whole network processing is complete. If the exclusion is successful, the LED will flash white -> green ->white -> green and then LED will pulse a blue. If failed, the yellow LED lasts for 30 seconds, then the green LED flashes once.

Device Wake-Up

Press and hold the button at least 2s until Red Led is on and then release the button,device will send wakeup notification to controller if device is in a Z-Wave network.

Factory Reset

1. Power up the device.

2. Press and hold the button for 15s until Red Led is blinking,then release the button

Note: Please use this procedure only when the network primary controller is missing or otherwise inoperable.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Battery Type

Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

Battery Quantity

Enter the number of batteries of the designated type that the product uses.

Color

If the product is only available in one color, pick the color from the list.

Sensors

Sensor types supported by the product.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).

Opiniones

grado

Juan F. 22/02/2022

Le meti los parametros

Set these parameter settings:

Parameter 3 [2 byte] = 10 // This will set the timeout of the PIR sensor to 10 seconds

Parameter 4 [1 byte] = 5 // This is the default setting, but sending it in anyways may active the PIR sensor

Parameter 5 [1 byte] = 2 // After setting param 3 and 4, i would test the unit first before setting this. This changes the report type to your gateway.