Productos más vistos

Sensor de temperatura...

Secure SES302 es el sensor de...

Sensor de temperatura para interior Secure SES302

Ver más grande

Este producto se compra "Bajo Pedido"

Sensor de temperatura para interior Secure SES302

Referencia SES302

Estado: Nuevo

Secure SES302 es el sensor de temperatura que permite mediciones a través de cables auxiliares, NTC, sensores para tubo y deposito ...

Más detalles

Sin Stock

Eliminar de mis favoritos
Agregar este producto a mis favoritos
Imprimir

Descripción

Sensor de temperatura Z-Wave

Secure SES302 es la sonda que permite la medición de la temperatura de las condiciones internas.

Está alimentado por 2 baterías AA y está certificado Z-Wave Plus.
Además de su función principal, es posible cablear varias sondas externas Secure en el módulo, ya sea:

1 sensor de temperatura NTC externo (SES001)
4 sensores de temperatura por cable para tubería o deposito (SES002) conectados por cables 1m
1 sensor de temperatura por cable para tubería o tanque (SES003) conectado por un cable 4m

Estos módulos son ideales para la medición de temperatura en aplicaciones con controles de calefacción central u otra aplicación similar. Su interfaz de usuario es simple, con un pulsador local y los indicadores LED en la parte posterior.

Es fácil de incluir / excluir en una red Z-Wave.

CARACTERÍSTICAS:

La medición precisa de la temperatura
Aplicación en los sistemas de control dinámico para tanques / tubos / calefacción por suelo radiante / ...
Posibilidad de conexión de sonda externa
Interropérable con productos y sistemas de certificación Z-Wave
fácil Instalación
Informe de batería baja

CARACTERÍSTICAS TÉCNICAS:

Tipo: Portable montaje / pared
rango de medición de temperatura: ± 0,5 ° C desde 0 ° C a 40 ° C
el chip Z-Wave Más
Frecuencia: 868.42 MHz
Fuente de alimentación: 2x AA (LR6)
Rango: hasta 100 m en el exterior
Protección: IP30
Dimensiones: 86 x 85 x 30 mm

Información Ampliada Z-Wave (Inglés)

Nombre: Environmental Sensor

Fabricante:Secure Controls (UK)

Identificador:SES 302

Número de Certificación Z-Wave:ZC10-15010007

Plataforma Hardware:ZM5202

FLiRS:NO

Tipo de Role:Reporting Sleeping Slave

Descripción Corta:The Environmental Sensor (SES 302) is a temperature sensor, which also supports four external digital temperature sensors or one external analog temperature sensor.

Descripción:The Environmental Sensor (SES 302) measures temperature. The sensor is battery-operated devices which transmit information to an associated device in a network. It can support either 1 thermistor (SES 001) or up to 4 external digital temperature sensors (SES 002/003). SES 302 operates on 2x AA batteries, providing a nominal life of 2 years (with on-board sensors operating with the default configuration).

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

Z-Wave Plus Lifeline, in which multilevel sensor report, Battery low alarm are reported. Each endpoint supports 1 association group.

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

Delta Temperature

This Parameter is used to configure the delta based temperature report. To configure Delta temperature reporting to 2 °C. The value need to configured in device is 2/0.1 = 20. Controllers may only allow configuring signed values. In order to set values in the range 128…255, the value sent in the application shall be equal to desired value minus 256. For example, to set Delta Temperature to 130, it may be needed to set a value 130−256=−126.

Temp Reporting Intervals

This Parameter is used to configure the time interval based temperature report. Controllers may only allow configuring signed values. In order to set values in the range 128…255, the value sent in the application shall be equal to desired value minus 256. For example, to set Delta Temperature to 130, it may be needed to set a value 130−256=−126.

Exclusion

Step 1.On the Z-Wave controller, select exclusion for removing a device from the network.
Step 2: On the SES 302, press the button, hold and release after 1 second to send a request (Network Information Frame) to remove from the network. On successful exclusion the LED will flash 2 times. The total process can take up to 2 seconds. If the LED flashes 4-times this means that the exclusion process has failed, so try moving the SES 302 to another position and repeat the exclusion steps. The controller will show when the exclusion operation is successful.

Learn Mode (adding another controller)

Not applicable

Factory Reset

Please use this procedure only when the primary controller is missing or otherwise inoperable.
To reset the device to factory resst, press the button 3 times within 3 seconds it will put the device in factory default, that include setting all the configuration, Association to factory default and removing the device from Z-Wave network.

Additional Special Features

None

Inclusion

Step 1.On the Z-Wave controller, select Include for adding a device to the network.
Step 2: On the SES 302, press the button, hold and release after 1 second to send a request (Network Information Frame) to join the network. On successful inclusion the LED will flash 2 times. The total process can take up to 20 seconds. If the LED flashes 4-times this means that the inclusion process has failed, so try moving the SES 302 to another position and repeat the Inclusion steps. If the inclusion process fails again, the device may be already included in another network. So first exclude and then include the device. The controller will show when the inclusion operation is successful.

Device Wake-Up

Device can be wakeup by button press of more then one second, devcie will stay in wakeup state for about 10 seconds.
device will also wakeup on the every wakeup interval configured by controller. The minimum wakeup interval can be configured is 2 minutes and maximum wakeup interval can be configured is 24 hours in setps of one minte.
Default wakeup interval is 24 hours.