Secure SSR303 Z-Wave Plus Actuador de 3A para calderas GEN5

Referencia SECESSR303-5

Estado: Nuevo

El relé actuador controlado medinate Z-Wave Plus Secure SSR303 Gen5 permite operar cargas de hasta 3A / 230 V de forma inalámbrica. Resulta ideal para controlar calderas de agua caliente o electrovávulas.

Más detalles

Sin Stock

Eliminar de mis favoritos
Agregar este producto a mis favoritos
Imprimir

Características técnicas

Tecnología Domótica	Z-Wave Plus

Descripción

El relé controlado sin cables mediante tecnologñia Z-Wave Plus Secure SSR303 Gen5 permite operar cargas de hasta 3 A / 230 V. Su uso está destinado para controlar calderas de agua caliente o electroválvulas . El dispositivo se puede operar localmente gracias a sus dos botones. Un LED indica el estado del dispositivo (on/off). El moderno y elegante diseño del dispositivo permite ubicarlo en la pared en posiciones visibles en el hogar.

Datos técnicos

Tipo de dispositivo: Z-Wave Plus esclavo con enrutamiento/repetidor
Indice de protección: IP 30
Dimensiones: 86mm x 86 mm x 36,25 mm
Diseño Estándar: EN60730
Carga máxima: 3 A a 230V

Información Ampliada Z-Wave (Inglés)

Nombre: SSR 303 (Single Channel On/Off Power switch)

Fabricante:Secure Controls (UK)

Identificador:MAX10Z-384

Número de Certificación Z-Wave:ZC10-16075134

Plataforma Hardware:ZM5202

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:The SSR 303 is a single channel relay/switch, it forms part of central heating control system, it can be operated by any third party controllers/Thermostat using ‘Binary Switch CC’ commands.

Descripción:The SSR 303 is a single channel relay/switch, it forms part of central heating control system, it can be operated by any third party controllers/Thermostat using ‘Binary Switch CC’ commands. SSR 303 will act as a repeater once added into the Z- Wave network, providing an alternative communication route for units which otherwise would not be within communication distance of each other. SSR 303 has a fail-safe mode where by the relay is turned OFF if another 'Thermostat Mode SET' command has not been received within 60 minutes.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

Z-Wave Plus Lifeline group, SSR 303 will send unsolicited SWITCH BINARY REPORT to lifeline group.

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

Inclusion

STEP 1: Ensure the Network LED is flashing on the SSR 303, if not follow ‘Exclusion’ steps first.

STEP 2: Put the 3rd party controller into inclusion mode.

STEP 3: Press and hold the network button on the SSR 303 until the ‘ON’ LED’s start flashing.

The SSR 303 has been added onto the network when the ‘OFF’ LED goes solid red.

NOTE: If the ON LED does not flash then the add process has been unsuccessful.

Exclusion

STEP 1: Put the 3rd party controller into exclusion mode.

STEP 2: Press and hold the network button on the SSR 303.

The SSR 303 has been removed from the network when the Network LED starts flashing.

NOTE: If the Network LED does not flash the remove process has been unsuccessful.

Factory Reset

""Please use this procedure only when the primary controller is missing or otherwise inoperable.""

Follow ‘Exclusion’ steps.

Additional Special Features

SSR 303 has a fail-safe mode where by the relay is turned OFF if another 'Thermostat Mode SET' command has not been received within 60 minutes.

Color

If the product is only available in one color, pick the color from the list.

IP (Ingress Protection) Rated

Product is suitable for Outdoor use and is waterproof under an IP (Ingress Protection) rating system.

Electric Load Type

Select the electric load type(s) supported by the device.

Switch Load Capacity Current

The amount of switch load energy the product is rated for in Amps