Heatit Z-TRM3 termostato Z-Wave Plus para suelo radiante

Características técnicas

Tecnología	Z-Wave Plus

Descripción

Heatit Z-TRM3 es un termostato electrónico, para usar sobre todo con suelo radiante (calefacción por suelo radiante electrica o de agua caliente y electroválvulas de 220V). Diseñado para ser montado en una caja de empotrar o caja de mecanismos estándar. El termostato tiene un chip Z-Wave+ incorporado que puede ser conectado con sistemas de domótica de esta tecnología. El Termopstato Heatit Z-TRM3 está equipado con un interruptor unipolar y encaja en los marcos del Sistema 55. El termostato puede soportar una carga máxima de 16A /3600W a 230V. También puede ser utilizado para calefacción a base de agua si el termostato está conectado a Heatit Z-Water. Por supuesto también actuando directamente sobre las elecroválvulas de calefacción.

CARACTERÍSTICAS

Sensor del suelo (incluido. es opcional su instalación)
Sensor interno de la habitación
Sensor de habitación externa (conectado por cable: opcional)
Limitador de temperatura
SmartStart
Programa semanal/restauración a través de la puerta de enlace
Temperatura leída en el display
Actualización del firmware (OTA)
Medición de la energía
LED de estado de los relés
interruptor unipolar
Modo de bloqueo/desbloqueo de niños
Calibración
5 asociaciones
Soporta el modo de encriptación: S0, S2 Clase autenticada, S2 Clase no autenticada
Este producto es un producto de seguridad Z-Wave Plus con encriptación. El producto debe ser utilizado con un controlador de seguridad Z-Wave para poder utilizarlo completamente.

DATOS TÉCNICOS

Protocolo de radio Z-Wave - 868,4MHz
Chip Z-Wave 500 chip
Tensión nominal 230V 50/60Hz
Carga máxima 3600W (carga resistiva) 750W cable calefactor autolimitado
Corriente máxima 16A
Consumo de energía <2,0W
Temperatura ambiente 0°C a 40°C (durante el funcionamiento)
Rango de temperatura de 5°C a 40°C
Histéresis 0,3°C a 3,0°C (por defecto 0,5°C)
Compatible con los sensores NTC con valores de 10, 12, 15, 22, 33 y 47 kΩ a 25°C
Código IP IP 21
Aprobaciones Z-Wave Plus, CE, EN 60730-1, EN 60730-2-9, EMC 2014/30/UE, RoHS 2011/65/UE, LVD 2014/35/UE

Alcance de la señal de radiofrecuencia (nº máximo de metros): 40

SDK: 6,81.06

Dimensión máxima de conexión (mm²):2,5mm²

Humedad ambiental máxima (%RH):80% RF

Temperatura máxima de regulación (ºC):40

Temperatura máxima sin carga (°C):40

Temperatura máxima con carga (°C):35

Tipo de modelo:Termostato

Altura del producto (mm): 52

Longitud del producto (mm):86

Peso del producto (gramo):109

Anchura del producto (mm):86

Tipo de chip IOT:Chip Z-Wave 500

Modo de encriptación Z-Wave: S0, S2 Clase Autenticada, S2 Clase No Autenticada, encriptación AES-128

DIMENSIONES

Tamaño Termostato Z-Wave Heatit Z-TRM3

Información Ampliada Z-Wave (Inglés)

Nombre: Heatit Z-TRM3

Fabricante:HEATIT

Identificador:Z-TRM3

Número de Certificación Z-Wave:ZC10-20036889

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:Heatit Z-TRM3 is an electronic thermostat for electrical floor heating, designed to be mounted in a standard flush box. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems. Heatit Z-TRM3 has SmartStart.

Descripción:Heatit Z-TRM3 is an electronic thermostat for electrical floor heating, designed to be mounted in a standard flush box. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems. Heatit Z-TRM3 has SmartStart. This feature allows the user to include all devices with SmartStart by scanning the QR codes on the devices. On startup all the devices will automatically be included in the gateway (requires SmartStart compability). This saves the installer a lot of work. Heatit Z-TRM3 is equipped with a single pole switch and fits into System 55 frames. The thermostat can withstand a load of max 16A /3600W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors. The thermostat has the capacity of up to 5 associations (relays, wall plugs etc.). The thermostat is designed for electrical heating. It may be used for waterbased heating if the thermostat is linked with the Heatit Z-Water.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

5

Lifeline. Normally used by the Z-Wave Controller

2

5

Send Binary Switch Set commands representing the status of the internal relay

3

5

Send Multilevel Sensor Reports for internal temperature sensor

4

5

Send Multilevel Sensor Reports for external room temperature sensor

5

Send Multilevel Sensor Reports for floor sensor

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

1

Operation mode

10

1

0

Room sensor calibration (A)

Room sensor calibration (A) NB. To set a negative value, use 256 and subtract the desired value.

11

1

0

Floor sensor calibration

Floor sensor calibration. NB. To set a negative value, use 256 and subtract the desired value.

12

1

0

External sensor calibration

External sensor calibration. NB. To set a negative value, use 256 and subtract the desired value.

13

1

0

Temperature display

Temperature display. Selects which temperature is shown on the display. Refer to Chapter 11 ”Standby and main screen”.

14

1

50

Button brightness – dimmed state

Button brightness – dimmed state. Configure the brightness of the buttons in dimmed state.

15

1

100

Button brightness – active state

Button brightness – active state. Configure the brightness of the buttons in active state.

16

1

50

Display brightness – dimmed state

Display brightness – dimmed state. Configure the brightness of the display in dimmed state.

17

1

100

Display brightness – active state

Display brightness – active state. Configure the brightness of the display, in active state.

18

2

60

Temperature report interval

Temperature report interval. Time interval between consecutive temperature reports. Temperature reports can also be sent as a result of polling.

19

1

10

Temperature report hysteresis

Temperature report hysteresis. The temperature report will be sent if there is a difference in temperature value from the previous value reported, defined in this parameter (hysteresis). Temperature reports can also be sent as a result of polling.

2

1

Sensor mode

20

2

90

Meter report interval.

Meter report interval. Time interval between consecutive meter reports. Meter reports can also be sent as a result of polling.

21

1

10

Meter report delta value

Meter report delta value. Delta value in kWh between consecutive meter reports. Meter reports can also be sent as a result of polling.

3

1

0

Floor sensor type

4

1

5

Temperature control hysteresis (DIFF I)

5

2

50

Floor minimum temperature limit (FLo)

6

2

400

Floor maximum temperature limit (FHi)

7

2

50

Air (A2) minimum temperature limit (ALo)

8

2

400

Air (A2) maximum temperature limit (AHi)

9

2

210

Heating mode setpoint

Meter V3

COMMAND_CLASS_METER_V3

Sensor Multilevel V5

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

Thermostat Mode V3

COMMAND_CLASS_THERMOSTAT_MODE_V3

Thermostat Operating State

COMMAND_CLASS_THERMOSTAT_OPERATING_STATE

Thermostat Setpoint V3

COMMAND_CLASS_THERMOSTAT_SETPOINT_V3

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Configuration V3

COMMAND_CLASS_CONFIGURATION_V3

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Multilevel V5

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

Supervision

COMMAND_CLASS_SUPERVISION

Thermostat Mode V3

COMMAND_CLASS_THERMOSTAT_MODE_V3

Thermostat Operating State

COMMAND_CLASS_THERMOSTAT_OPERATING_STATE

Thermostat Setpoint V3

COMMAND_CLASS_THERMOSTAT_SETPOINT_V3

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

The Z-Wave DSK can be found in the QR-Code and is located in 3 locations;

1. On the product box.

2. On the physical product, placed on the black plastic underneath the front.

3. On the PCB internally.

Classic Exclusion

Remove.

The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings.

Removing mode is indicated on the display by rotating LED segments on the display. This lasts until the timeout occurs after 90 seconds, or until the module has been added/removed in the network. Confirmation will show Inc/EcL on the display. Exit programming mode by choosing ESC in the menu. Your thermostat is

now ready for use with default settings.

NB! When the thermostat is removed from the gateway, the parameters are not reset.

Other Special Features

Chapter 8. Principles of regulation

Chapter 11. Standby and main screen

Chapter 12. Choice of sensor

Chapter 13. Selecting the right value for your external floor sensor

Chapter 14. Calibration

Chapter 17. Min/Max temperature settings

Chapter 18.1 Display on/off

Chapter 18.2 Childlock

Factory Reset Procedure

By pressing buttons Right and Center (down and confirm) for 20 seconds, the thermostat will perform a complete factory reset.

NB! Please use this procedure only when the primary controller/gateway is missing or otherwise inoperable.

The device will display rES for 10 seconds while performing a factory reset. When rES no longer is displayed, the thermostat has been reset.

Classic Inclusion

Add.

The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added from the network if the primary controller is in add mode.

There are two ways to add the Heatit Z-TRM3 to a Z-Wave network.

METHOD 1: STANDARD (MANUAL)

1. Press Center (confirm) for 10 seconds. The display will show OFF.

2. Press Right (down) 5 times until you see Con on the display.

3. Start the add/remove device process in your primary controller.

4. Start the add/remove mode in the Heatit Z-TRM3 by pressing Center (confirm) for approximately 2 seconds.

Adding mode is indicated on the display by rotating LED segments on the display. This lasts until the timeout occurs after 90 seconds, or until the module has been added in the network. Confirmation will show Inc/EcL on the display. Exit programming mode by choosing ESC in the menu. Your thermostat is now ready for use with default settings.

METHOD 2: SMARTSTART (AUTOMATIC)

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR-Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

IP (Ingress Protection) Rated

Product is suitable for Outdoor use and is waterproof under an IP (Ingress Protection) rating system.

Switch Type

Describes the type of operator for a switch.

Thermostat HVAC Systems Supported

Indicate which HVAC system or systems are supported by the thermostat.

Thermostat Modes

Select the mode(s) supported by the thermostat.