Produtos visualizados





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es
Reduced price! FIBARO Roller Shutter 3 View larger

FIBARO Roller Shutter 3

FGR-223

Novo

O obturador de rolo 3 da Fibaro permite controlar motores de obturador com chaves de limite eletrônicas e mecânicas, venezianas ou até mesmo portas de garagem.

Mais detalhes

Em estoque

63,89 €

-20%

79,86 €

Características tecnicas

Tecnologia Domótica Z-Wave Plus

Mais Informação

FIBARO Roller Shutter 3


FIBARO Roller Shutter 3 é uma nova versão do controlador do obturador / motor via rádio baseado na tecnologia Z-Wave. Trabalha com persianas motorizadas, venezianas, toldos e portões. Fibaro Roller Shutter 3 é alimentado por uma corrente monofásica de 220V e fornece um posicionamento preciso de persianas, toldos ou portões para que eles possam ser colocados na posição que você escolher. O módulo também é equipado com uma função de medição de energia quando usado com um centro de automação residencial da tecnologia Z-Wave.

Design comprovado, tecnologia sofisticada e ainda melhor: o novo Roller Shutter 3!

O FIBARO Roller Shutter 3 possui o chip GEN5 com a certificação Z-Wave Plus. Como de costume, integra suas persianas, toldos, persianas elétricas e portas de garagem na rede Z-Wave.

Graças ao Fibaro Roller Shutter 3, qualquer dispositivo alimentado por um motor elétrico AC pode ser controlado remotamente. O módulo de controle cego permite o posicionamento preciso dos motores com chave final mecânica e elétrica. Além disso, o dispositivo permite monitorar seu status.

Devido ao controle com botão / interruptor convencional, por aplicação ou com cenas pré-configuradas, você pode tornar sua vida mais confortável. Mesmo se você já estiver deitado na cama, feche suas persianas confortavelmente sem ter que se levantar. O rolo cego 3 também contribui para a segurança. Quando você sair de casa, feche todas as janelas e persianas simplesmente pressionando um único botão.

O módulo de rádio compacto é colocado em uma caixa de parede logo atrás do interruptor normal. O switch não está mais diretamente conectado à carga, mas atua como um dispositivo de entrada para o micromódulo FIBARO, que na verdade controla a carga. O switch envia apenas o sinal de controle para a inserção que controla a carga novamente. A solução funciona com todo o design do switch. Recomenda-se a utilização de caixas de parede com 65 mm de profundidade. Mas você também pode usar caixas menores com apenas 45 mm de profundidade se houver espaço suficiente atrás do comutador. O espaço disponível depende do tamanho do interruptor tradicional, das dimensões da caixa de parede e da quantidade de fiação adicional colocada nesta caixa.

Características:

Módulo de rádio embutido para a integração de instalações existentes (persianas, toldos, portas de garagem ...) em uma rede Z-Wave
Precisão do posicionamento do motor.
Carga máxima: 4.2A (resistiva), 1.7A (indutiva)
Função de medição de energia
Opera com interruptores momentâneos ou de alavanca ou com chaves de controle de obturador de rolo dedicadas
Permite a ativação da cena por comutação física.
Fonte de alimentação: 110 - 240VAC, 50 / 60Hz
Fiação: requer neutro
Consumo de energia: <0.8W
Tecnologia sem fio: Z-Wave Plus

Dimensões (LxAxL) 42 x 37 x 16 mm
Z-Wave Plus sim
Z-Wave S2 sim
REEE sim

Certificações de acordo com as normas europeias RoHS 2011/65 / EU
LVD 2006/95 / CE
EMC 2004/108 / EC
R & TTE 1999/5 / EC

Informação alargada da Z-Wave (Inglês)

Nome: Roller Shutter 3
Fabricante:FIBARO
Identificador:FGR-223
Número de Certificação Z-Wave :ZC10-19046413
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :FIBARO Roller Shutter 3 is a device designed to control roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices.
Descrição :FIBARO Roller Shutter 3 is a device designed to control roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices. Roller Shutter 3 allows precise positioning of roller blinds or venetian blind lamellas. The device is equipped with power and energy monitoring. It allows to control connected devices either via the Z-Wave network or via a switch connected directly to it. Main features of FIBARO Roller Shutter 3: - Compatible with any Z-Wave or Z-Wave Plus Controller, - Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 with PRNG-based encryption, - To be installed with roller blind motors with electronic or mechanical limit switches, - Advanced microprocessor control, - Active power and energy metering functionality, - Works with various types of switches – momentary, toggle and dedicated roller blind switches, - To be installed in wall switch boxes, - Works as a Z-Wave signal repeater.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
“Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2
5
“Roller Shutter” is assigned to shutter position control – UP/DOWN (uses Switch Multilevel command class).
3
5
“Slats” is assigned to slats position control – UP/DOWN (uses Switch Multilevel command class).
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
150
1
0
Force calibration
By setting this parameter to 2 the device enters the calibration mode. The parameter relevant only if the device is set to work in positioning mode (parameter 151 set to 1, 2 or 4).
151
1
1
Operating mode
This parameter allows adjusting operation according to the connected device.
152
4
150
Venetian blind - time of full turn of the slats
For Venetian blinds (parameter 151 set to 2) the parameter determines time of full turn cycle of the slats. For gates (parameter 151 set to 3 or 4) the parameter determines time after which open gate will start closing automatically (if set to 0, gate will not close). The parameter is irrelevant for other modes.
153
1
1
Set slats back to previous position
For Venetian blinds (parameter 151 set to 2) the parameter determines slats positioning in various situations. The parameter is irrelevant for other modes. NOTE: If parameter 20 is set to 1 (toggle switch), change value of parameter 153 to 0 for slats to work properly.
154
2
10
Delay motor stop after reaching end switch
For blinds (parameter 151 set to 1, 2, 5 or 6) the parameter determines the time after which the motor will be stopped after end switch contacts are closed. For gates (parameter 151 set to 3 or 4) the parameter determines time after which the gate will start closing automatically if S2 contacts are opened (if set to 0, gate will not close).
155
2
10
Motor operation detection
Power threshold to be interpreted as reaching a limit switch.
156
4
6000
Time of up movement
This parameter determines the time needed for roller blinds to reach the top. For modes with positioning value is set automatically during calibration, otherwise it must be set manually.
157
4
6000
Time of down movement
This parameter determines time needed for roller blinds to reach the bottom. For modes with positioning value is set automatically during calibration, otherwise it must be set manually.
20
1
2
Switch type
This parameter defines as what type the device should treat the switch connected to the S1 and S2 terminals. This parameter is not relevant in gate operating modes (parameter 151 set to 3 or 4). In this case switch always works as a momentary and has to be connected to S1 terminal.
24
1
0
Inputs orientation
This parameter allows reversing the operation of switches connected to S1 and S2 without changing the wiring.
25
1
0
Outputs orientation
This parameter allows reversing the operation of Q1 and Q2 without changing the wiring (in case of invalid motor connection) to ensure proper operation.
30
4
0
Alarm configuration - 1st slot
This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification. NOTE: Alarm with lower number has the higher priority, thus first alarm will override other alarms with the same type. NOTE: Setting Notification Value to 0xFF will result in launching the action twice: when alarm occurs and is cancelled.
31
4
0
Alarm configuration - 2nd slot (Water)
This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.
32
4
0
Alarm configuration - 3rd slot (Smoke)
This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.
33
4
0
Alarm configuration - 4th slot (CO)
This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.
34
4
0
Alarm configuration - 5th slot (Heat)
This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.
40
1
0
S1 switch - scenes sent
This parameter determines which actions result in sending scene IDs assigned to them. NOTE: Parameter 40 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent. NOTE: Enabling triple click for S1 in parameter 40 disables the ability to add/remove via S1.
41
1
0
S2 switch - scenes sent
This parameter determines which actions result in sending scene IDs assigned to them. NOTE: Parameter 41 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent.
60
1
0
Measuring power consumed by the device itself
This parameter determines whether the power metering should include the amount of active power consumed by the device itself.
61
2
15
Power reports - on change
This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. For loads under 50W, the parameter is not relevant and reports are sent every 5W change. Power report are sent no often then every 30 seconds.
62
2
3600
Power reports - periodic
This parameter determines in what time intervals the periodic power reports are sent to the main controller. Periodic reports do not depend on power change (parameter 61).
65
2
10
Energy reports - on change
This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller.
66
2
3600
Energy reports - periodic
This parameter determines in what time intervals the periodic energy reports are sent to the main controller. Periodic reports do not depend on energy change (parameter 65).
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Central Scene V3
COMMAND_CLASS_CENTRAL_SCENE_V3
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Protection V2
COMMAND_CLASS_PROTECTION_V2
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Supervision
COMMAND_CLASS_SUPERVISION
Switch Multilevel V4
COMMAND_CLASS_SWITCH_MULTILEVEL_V4
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
To remove the device from the Z-Wave network:

1. Make sure the device is powered.

2. Identify the S1 switch.

3. Set the main controller in remove mode (see the controller’s manual).

4. Quickly, triple click the S1 switch.

5. Wait for the removing process to end.

6. Successful removing will be confirmed by the Z-Wave controller’s message.

Device Wake-Up
FIBARO Roller Shutter 3 is powered with mains voltage so it is always awake.
Inclusion
To add the device to the Z-Wave network manually:

1. Power the device.

2. Identify the S1 switch.

3. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual).

4. Quickly, triple click the S1 switch.

5. If you are adding in Security S2, scan the DSK QR code or input the underlined part of the DSK (label on the bottom of the box).

6. Wait for the adding process to end.

7. Successful adding will be confirmed by the Z-Wave controller’s message.



To add the device to the Z-Wave network using Smart Start:

1. Set the main controller in Security S2 Authenticated add mode (see the controller’s manual)

2. Scan the DSK QR code or input the underlined part of the DSK

3. (label on the bottom of the box).

4. Power the device (turn on the mains voltage).

5. LED will start blinking yellow, wait for the adding process to end.

6. Successful adding will be confirmed by the Z-Wave controller’s message.



Factory Reset
Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted.

1. Switch off the mains voltage (disable the fuse).

2. Remove the device from the wall switch box.

3. Switch on the mains voltage.

4. Press and hold the B-button to enter the menu.

5. Wait for the LED indicator to glow yellow.

6. Quickly release and click the B-button again.

7. After few seconds the device will be restarted, which is signalled with the red LED indicator colour.

Please use this procedure only when the network primary controller is missing or otherwise inoperable.""

S2 Authenticated
S2_AUTHENTICATED
Color
If the product is only available in one color, pick the color from the list.
Electric Load Type
Select the electric load type(s) supported by the device.
Sensors
Sensor types supported by the product.
Supported Meter Type
Indicate which type of metering is supported by the device.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Window Covering Control Features
Select the feature(s) supported in the Window Covering Control product.
Loads Controlled
The number of different loads controllable by the product if it supports more than one.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps

 

Avaliações

Nota 
2021-11-25

Domotizar persianas en Home Assistant

Llevo varios meses de uso en Home Assitant (ahora ya tengo 5 persianas) y estoy muy satisfecho con estos dispositivos de Fibaro. La respuesta es inmediata. Cierto es que la integración con HA tiene sus peculiaridades pero he conseguido tener un sistema estable y "barato"

Nota 
2021-11-25

Magnifico para domotizar persianas

Funcionan muy bien con Home Center 3 y Alexa

Nota 
2020-09-17

Funciona bien en eedomus

Se integra bien en eedomus. Me llego rapido y no tuve problemas. Gracias.

Faça uma avaliação!

Escrever uma avaliação

FIBARO Roller Shutter 3

FIBARO Roller Shutter 3

O obturador de rolo 3 da Fibaro permite controlar motores de obturador com chaves de limite eletrônicas e mecânicas, venezianas ou até mesmo portas de garagem.

Accessories

11 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: