Heatit Z-Dim2 - dimmer rotacional Z-Wave

Características tecnicas

Tecnologia Domótica	Z-Wave Plus
Recurso	Dimmer

Mais Informação

Heatit Z-Dim2 é um dimmer rotativo Z-Wave para muitos tipos de fontes de luz. O Heatit Z-Dim2 funciona com cargas baixas sem que as luzes pisquem. Escurece lâmpadas LED de 1-200VA, lâmpadas incandescentes e halógenas de 230V, drivers de LED reguláveis e transformadores eletrônicos. Os fios L+N devem ser conectados.

O regulador está equipado com uma opção de comutação multidirecional. Isso permite que você ligue e regule uma fonte de luz de um dimmer e, em seguida, desligue-a com outro interruptor. Muito prático para escadas, corredores longos, etc.

O Heatit Z-Dim2 é adequado para LEDs e se encaixa nos quadros do System 55. Ao conectar cargas baixas, é recomendável usar um bypass

Informação alargada da Z-Wave (Inglês)

Nome: Heatit Z-Dim2

Fabricante:Heatit controls

Identificador:Z-Dim2

Número de Certificação Z-Wave :ZC14-22060111

Plataforma de Hardware :ZGM130S037HGN2 / ZGM130S037HGN1

FLiRS:Não

Tipo de Role :Always On Slave

Descrição breve :Heatit Z-Dim2 is a Z-Wave™ rotary dimmer for many different types of light fixtures. The Heatit Z-Dim2 works on most low loads without causing flickering. The dimmer is equipped with an external switch option. This allows you to dim and turn on/off the load from an external switch.

Descrição :Heatit Z-Dim2 is a Z-Wave™ rotary dimmer for many different types of light fixtures. The Heatit Z-Dim2 works on most low loads without causing flickering. The dimmer is equipped with an external switch option. This allows you to dim and turn on/off the load from an external switch.

Grupo

Nodos máximos

Descrição

1

5

2

5

3

5

Número

Tamanho (Bytes)

Valor por defeito

Nome

Descrição

1

100

Power restore level

10

1

0

Load dimming mode

11

1

90

Maximum dim level

12

1

10

Meter report threshold

13

2

780

Meter report interval

2

1

0

Switch ON level

3

4

0

Automatic turn OFF

4

0

Automatic turn On

5

1

0

Turn off delay time

6

1

0

Rotary wheel press functionality

7

1

0

External switch functionality

8

1

50

Dimming duration

9

1

0

Choose the dimmer curve

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Information (AGI) V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Central Scene V3

COMMAND_CLASS_CENTRAL_SCENE_V3

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multilevel Switch V4

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security 0

COMMAND_CLASS_SECURITY

Security 2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

The QR-Code is needed when including a device using S2 security or SmartStart. The DSK can be found in the QR-Code and is located;

• On the product.

• On the Quick Guide.

• On the gift box.

Classic Inclusion

The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode.

Method 1: Standard (Manual)

Add mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been added to the network. To start the configuration process press the Reset button, or the external switch connected to P, 3 times in rapid succession. The LED will blink green for 3 seconds if adding is successful. The device is now ready for use with default settings.

Classic Exclusion

The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings.

Remove mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been removed from the network. To start the configuration process press the Reset button, or the external switch connected to P, 3 times in rapid succession. The LED will blink green for 3 seconds if removing is successful. The device is now ready for use with default settings.

Factory Reset Procedure

Press and hold the reset button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will shine solid green for 3 seconds. You may now release the button.

Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Other Special Features

• 2-wire

• Firmware update (OTA)

• Overload protection

• Short circuit protection

• Surge protection

• Overheat protection

• External switch

• Min. dim level

• Max. dim level auto-calibration

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Electric Load Type

Select the electric load type(s) supported by the device.

Switch Load Capacity Watts

The amount of switch load energy the product is rated for in Watts

Switch Type

Describes the type of operator for a switch.

Z-Wave Scene Type

Indicates which of the two types of Z-Wave scene command classes are supported. Scenes or Central Scene