Produtos visualizados

FIBARO - Walli Dimmer

O regulador FIBARO Walli Dimmer é um...

Reduced price! FIBARO - Walli Dimmer

View larger

FIBARO - Walli Dimmer

Referência: FGWDEU-111

Estado: Novo

O regulador FIBARO Walli Dimmer é um regulador inteligente com interruptor de luz integrado. Compatível com Z-Wave +.

Mais detalhes

Não disponível

Retirar este produto da minha lista de favoritos.
Adicionar este produto à minha lista de favoritos.
Print

Características tecnicas

Tecnologia Domótica	Z-Wave Plus
Recurso	Dimmer

Mais Informação

Interruptor Dimmer Inteligente Z-Wave + Fibaro Walli Dimmer

FIBARO Walli Dimmer é um dimmer inteligente com interruptor de luz integrado. Trabalha com fontes de iluminação disponíveis no mercado, tais como: LEDs, lâmpadas compactas, lâmpadas tradicionais e lâmpadas halógenas. O dispositivo está equipado com funções de calibração e medição automáticas para potência e energia ativas.

Design exclusivo e tecnologia excepcional

A série completa de conectores e conectores inteligentes FIBARO baseados na tecnologia Z-Wave proporcionará à sua casa uma inteligência versátil. O visual da série é inspirado em uma pérola - sua sofisticação intemporal e bela forma que completa qualquer interior.

Fibaro Walli

Anel LED para combinar com sua casa

Escolha sua cor favorita

Selecione a cor do anel de LED para adaptá-lo às suas preferências pessoais.

Botão duplo de luz de fundo

Use duas cores de luz de fundo onde quiser - uma cor diferente na parte inferior e outra na parte superior para ver o status exato do dispositivo.

Uma visão geral do consumo de energia

Controle a quantidade de energia consumida pelo equipamento em sua casa.

Componentes confiáveis e detalhes atraentes

Na FIBARO, qualidade e design únicos sempre andam de mãos dadas. A linha Walli foi projetada para melhorar o conforto e a segurança de sua família por muitos anos.

Fibaro Walli

Pulsações a gosto

Configure o botão de comutador Walli para aproveitar ao máximo seus incríveis recursos.

Um único clique para acender a luz, um duplo clique para desligá-lo, um clique triplo para ativar a cena "Fun", uma pulsação mantida para intensidade de luz de 60%.

Compatível com produtos de outros fabricantes

O FIBARO Walli é compatível (com adaptadores) com placas frontais de outros fabricantes: GIRA - System 55, Legrand - Céliane, Schneider - Odace. Se estiver conectado a tomadas e comutadores existentes, equipe-os com uma peça inteligente integrada e aproveite os recursos de uma casa inteligente sem precisar substituir o painel frontal.

Fibaro Walli

Gerencie toda a casa com voz

Os interruptores e tomadas inteligentes da Walli são totalmente compatíveis com os famosos assistentes de voz do Google Assistant e do Amazon Alexa. Gerenciamento de voz fácil e confortável de toda a casa.

Seja com sua casa onde quer que você esteja

A aplicação móvel FIBARO Home Center permite-lhe gerir interruptores e tomadas inteligentes com o seu smartphone, tablet ou smartwatch. Mantenha tudo sob controle como um chefe.

Consumo de energia controlada

Dê uma olhada em sua casa, analise o consumo de energia de seus aparelhos e otimize suas despesas como sempre quis.

Dê um passo adiante no futuro

A série Walli da FIBARO inclui interruptores e tomadas clássicas e não inteligentes para manter constante a estética da sua casa. Escolha-os como desejar e desfrute de um design e recursos exclusivos.

FUNÇÕES

Gerenciamento remoto de iluminação.
Controle de luz através de comandos de voz.
Adaptação do anel luminoso às preferências do usuário.
Notificações de falhas de equipamentos elétricos.
Controle do consumo de energia.

AS ESPECIFICAÇÕES TÉCNICAS

Potência: 110-230V 50 / 60Hz
Corrente de carga nominal:
Resistivo: incandescente e halogéneo 0,22-1,52A (50-350W)
Resistência capacitiva: lâmpada fluorescente (compacta / reator eletrônico), transformador eletrônico, LED 0.22-1.3A (30-300VA)
Resistivo-indutivo: transformadores ferromagnéticos 0.22-1.3A (30-300VA)
Com FIBARO Bypass 2: tubo fluorescente ou lâmpada LED (fator de potência> 0,5) 0,022-0,22A (5-50W)
Radiofreqüência: 868.0-868.6 megahertz
Âmbito: até 40 m no interior (dependendo do terreno e da estrutura do edifício)
Potência máxima de transmissão: + 6dBm
Temperatura de operação: 0-35 ° C
Umidade ambiente: 10-95% RH sem condensação
Para instalação em caixas: Ø = 60mm, profundidade e 40mm
Dimensões (A x L x P): 86 x 86 x 51 mm

Toda a documentação e instruções dos produtos Fibaro estão disponíveis no site manuals.fibaro.com

Informação alargada da Z-Wave (Inglês)

Nome: Wall Dimmer

Fabricante:FIBARO

Identificador:FGWDEU-111

Número de Certificação Z-Wave :ZC10-19056515

Plataforma de Hardware :ZM5101

FLiRS:Não

Tipo de Role :Always On Slave

Descrição breve :FIBARO Walli Dimmer is a smart wall dimmer designed to control light source via Z-Wave network.

Descrição :FIBARO Walli Dimmer is a smart wall dimmer designed to control light source via Z-Wave network. It measures active power and energy consumed by the controlled load. You can install it with provided cover plate or other compatible. Main features of FIBARO Walli Dimmer: - Can be used for dimming: o 110/230V operated conventional incandescent and halogen, o 12V operated ELV halogen lamps and dimmable LED bulbs (with electronic transformers), o 12V operated MLV halogen lamps (with ferromagnetic transformers), o dimmable LED bulbs, o dimmable compact fluorescent CFL tube lamps, o supported dimmable light sources (power factor > 0.5) with minimal power of 5VA using FIBARO Bypass 2. - Can be used for switching: o compact fluorescent CFL tube lamps with electronic ballast, o fluorescent tube lamps with electronic ballast, o LED bulbs (power factor > 0.7), o supported light sources (power factor > 0.5) with minimal power of 5VA using FIBARO Bypass 2. - Uses different operating modes: o „Trailing edge” for resistive loads (R) o „Trailing edge” for resistive-capacitive loads (RC) o „Leading edge” for resistive-inductive loads (RL) - Can be used with provided cover plate or one of the following: o GIRA – System 55 (Standard 55, E2, Event, Event Clear), o Legrand – Céliane, o Schneider – Odace. - Active power and energy consumption metering. - Can be installed in two and three-wired configuration. - Calibrates automatically to the connected light source. - Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption. - Works as Z-Wave signal repeater (all non-battery operated devices within the network will act as repeaters to increase reliability of the network). - May be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.

Descarregue o manual a partir de aqui.

Grupo

Nodos máximos

Descrição

1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).

2nd association group – “On/Off” is used to turn the associated devices on/off reflecting button operation (uses Basic command class).

3rd association group – “Dimmer” is used to change level of associated devices reflecting button operation (uses Switch Multilevel command class).

Número

Tamanho (Bytes)

Valor por defeito

Nome

Descrição

Remember device state

This parameter determines how the device will react in the event of power supply failure (e.g. power outage).

3500

LED frame – power limit

This parameter determines maximum active power. Exceeding it results in the LED frame flashing violet. Function is active only when parameter 11 is set to 8 or 9.

LED frame – colour when ON

This parameter defines the LED colour when thedevice is ON. When set to 8 or 9, LED frame colour will change depending on he measured power and parameter 10. Other colours are set permanently and do not depend on power consumption.

LED frame – colour when OFF

This parameter defines the LED colour when the device is OFF.

100

LED frame – brightness

This parameter allows to adjust the LED frame brightness.

150

Minimum brightness level

This parameter is set automatically during the calibration process, but can be changed manually after the calibration.

151

Maximum brightness level

This parameter is set automatically during the calibration process, but can be changed manually after the calibration.

152

Incandescence level of dimmable compact fluorescent lamps

The virtual value set as a percentage level between parameters MIN (1%) and MAX. (99%). The device will set to this value after the first switch on. It is required for warming up and switching dimmable compact fluorescent lamps and certain types of light sources.

153

Incandescence time of dimmable compact fluorescent lamps

This parameter determines the time required for switching compact fluorescent lamps and certain types of light sources. Setting this parameter to 0 will disable the incandescence functionality.

154

Automatic control – dimming step size

This parameter defines the percentage value of dimming step during the automatic control.

155

Automatic control – time of dimming step

This parameter defines the time of performing a single dimming step set in parameter 154 during the automatic control.

156

Manual control – dimming step size

This parameter defines the percentage value of the dimming step during the manual control.

157

Manual control – time of dimming step

This parameter defines the time of performing a single dimming step set in parameter 156 during the manual control.

158

Auto-off functionality

This parameter allows to automatically switch off the device after a specified time from switching the light source on. It may be useful when the device is installed in the stairway.

159

Force auto-calibration

Changing value of this parameter will force the calibration process. During the calibration parameter is set to 1 or 2 and switched to 0 upon completion.

160

Auto-calibration status (read-only parameter)

This parameter determines operating mode of the device (automatic/manual settings).

161

Burnt out bulb detection

This parameter defines percentage power variation (compared to power consumption measured during the calibration) to be interpreted as load error/burnt out bulb.

162

Time delay of a burnt out bulb and overload detection

This parameter defines detection delay for the burnt out bulb (parameter 161) and overload (parameter 2).

163

255

First button – Switch ON value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group.

164

Second button – Switch OFF value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group.

165

Double click – set level

This parameter defines brightness level set after double-clicking any of the buttons. The same value is also sent to devices associated with 2nd and 3rd association group.

170

Load control mode

This parameter allows to set the desired load control mode. Auto-calibration sets value of this parameter to 2 (control mode recognized during auto-calibration), but the installer may force control mode using this parameter. After changing parameter value, turn the load OFF and ON to change control mode.

171

Load control mode recognized during auto-calibration (read only)

This parameter allows to read load control mode that was set during auto-calibration.

172

ON/OFF mode

This mode is necessary while connecting non-dimmable light sources. Setting this parameter to 1 automatically ignores brightening/dimming time settings. Forced auto-calibration will set this parameter’s value to 2.

173

Dimmability of the load (read only)

This parameter allows to read if the load detected during calibration procedure is dimmable.

174

Soft-start functionality

This parameter allows to set time required to warm up the filament of halogen bulb.

175

Auto-calibration after power on

This parameter determines the trigger of auto-calibration procedure, e.g. power on, load error, etc.

176

Behaviour after OVERCURRENT or SURGE

Error occurrences related to surge or overcurrent results in turning off the output to prevent possible malfunction. By default the device performs three attempts to turn on the load (useful in case of temporary, short failures of the power supply).

177

255

Brightness level correction for flickering loads

Correction reduces spontaneous flickering of some capacitive loads (e.g. dimmable LEDs) at certain brightness levels in 2-wire installation. In countries using ripple-control, correction may cause changes in brightness. In this case it is necessary to disable correction or adjust the time of correction for flickering loads.

178

Method of calculating the active power

This parameter defines how to calculate active power. It is useful in a case of 2-wire connection with light sources other than resistive.

179

Approximated power at the maximum brightness level

This parameter determines the approximate value of the power that will be reported by the device at its maximum brightness level.

3500

Overload safety switch

This function allows to turn off the controlled device in case of exceeding the defined power. Controlled device can be turned back on via the button or sending a control frame.

Buttons orientation

This parameter allows reversing the operation of the buttons.

Alarm configuration - 1st slot

This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.

Alarm configuration - 2nd slot

Alarm configuration - 3rd slot

Alarm configuration - 4th slot

Alarm configuration - 5th slot

600

Alarm configuration – duration

This parameter defines duration of alarm sequence. When time set in this parameter elapses, alarm is cancelled, LED frame and relay restore normal operation, but do not recover state from before the alarm.

First button – scenes sent

This parameter determines which actions result in sending scene IDs assigned to them. Values can be combined (e.g. 1+2=3 means that scenes for single and double click are sent). Enabling scenes for triple click disables entering the device in learn mode by triple clicking.

Second button – scenes sent

Power reports – include self-consumption

This parameter determines whether the power measurements should include power consumed by the device itself.

Power reports – on change

This parameter defines minimal change (from the last reported) in measured power that results in sending new report. For loads under 50W the parameter is irrelevant, report are sent every 5W change.

3600

Power reports – periodic

This parameter defines reporting interval for measured power. Periodic reports are independent from changes in value (parameter 61).

Energy reports – on change

This parameter defines minimal change (from the last reported) in measured energy that results in sending new report.

3600

Energy reports – periodic

This parameter defines reporting interval for measured energy. Periodic reports are independent from changes in value (parameter 65).

Basic

COMMAND_CLASS_BASIC

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Information V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Central Scene V3

COMMAND_CLASS_CENTRAL_SCENE_V3

Configuration

COMMAND_CLASS_CONFIGURATION

CRC16 Encapsulation

COMMAND_CLASS_CRC_16_ENCAP

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Protection V2

COMMAND_CLASS_PROTECTION_V2

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Switch Multilevel V4

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Device Wake-Up

FIBARO Walli Dimmer is powered using DC power supply unit so it is always awake.

Factory Reset

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. Resetting to factory defaults does not reset energy consumption memory.

1. Quickly, three times click, then press and hold one of the buttons to enter menu.

2. Release the button when the device glows yellow.

3. Quickly click the button to confirm.

4. After a few seconds the device will be restarted, which is signalled with the red LED colour.

Please include a request to use the reset procedure only when the primary controller is missing or inoperable.

Exclusion

To remove the device from the Z-Wave network:

1. Set the main controller into remove mode (see the controller’s manual).

2. Quickly, three times click one of the buttons.

3. LED will start blinking yellow, wait for the removing process to end.

4. Successful removing will be confirmed by the Z-Wave controller’s message and red LED colour.

5. The device will start calibrating the load.

Inclusion

To add the device to the Z-Wave network manually:

1. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual).

2. Quickly, three times click one of the buttons.

3. If you are adding in Security S2 Authenticated, scan the DSK QR code or input the underlined part of the DSK (label on the bottom of the box).

4. LED will start blinking yellow, wait for the adding process to end.

5. Adding result will be confirmed by the Z-Wave controller’s message and the LED frame:

- Green - successful (non-secure, S0, S2 non-authenticated),

- Magenta - successful (Security S2 Authenticated),

- Red – not successful.

To add the device to the Z-Wave network using Smart Start:

1. Set the main controller in Security S2 Authenticated add mode (see the controller’s manual).

2. Scan the DSK QR code or input the underlined part of the DSK (label on the bottom of the box).

3. Power the device.

4. Wait for the calibration process to end. Light may blink, the device will be switched off once the process is completed.

5. Wait for the adding process to start (up to few minutes), which is signaled with yellow LED blinking.

6. Adding result will be confirmed by the Z-Wave controller’s message and the LED frame:

- Green - successful (non-secure, S0, S2 non-authenticated),

- Magenta - successful (Security S2 Authenticated),

- Red – not successful.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Loads Controlled

The number of different loads controllable by the product if it supports more than one.

Supported Meter Type

Indicate which type of metering is supported by the device.

Color

If the product is only available in one color, pick the color from the list.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).