Qubino Luxy Smart Switch - Z-Wave Smart Switch com luz e som

1

1

Supports following commands: COMMAND_CLASS_DEVICE_RESET_LOCALLY, DEVICE_RESET_LOCALLY_NOTIFICATION - triggered upon reset, COMMAND_CLASS_SWITCH_MULTILEVEL_V4, SWITCH_MULTILEVEL_REPORT_V4 - triggered upon change of brightness, COMMAND_CLASS_SWITCH_COLOR_V3, SWITCH_COLOR_REPORT_V3 - triggered upon change of color, COMMAND_CLASS_NOTIFICATION_V8, NOTIFICATION_REPORT_V8 - triggered upon change of alarm detection state or upon current overload detection, COMMAND_CLASS_SWITCH_BINARY, SWITCH_BINARY_REPORT - is triggered when a change of output state of relay occurs. COMMAND_CLASS_METER, METER_REPORT - triggered upon energy consumption change according to configuration parameters 40 and 42. CONFIGURATION_REPORT – triggered upon a local change of the working mode of the four capacitive buttons (see chapter 5.4) Reserved for communication with the primary gateway/hub. Used to report unsolicited messages to the controller.

2

5

Supports the following command: COMMAND_CLASS_BASIC_V2, BASIC_SET_V2 - is triggered when a change of output state occurs; LEDs are on/off.

3

5

Supports the following command: COMMAND_CLASS_SWITCH_MULTILEVEL_V4, SWITCH_MULTILEVEL_SET_V4 - is triggered when a change of output state occurs; brightness changes.

4

5

Supports the following command: COMMAND_CLASS_SWITCH_COLOR_V3, SWITCH_COLOR_SET_V3 - is triggered when a change of output state occurs; colour changes.

5

5

Supports the following command: COMMAND_CLASS_BASIC_V2, BASIC_SET_V2 - is triggered when a change of output state of relay occurs.

1

1

0

Parameter no. 1 – Relay contact type

Defines the contact type when open/closed contact. Values (size is 1-byte dec): • Default value 0 • 0 - NO (normally open) output type • 1 - NC (normally close) output type

10

2

0

Parameter no. 10. – auto on timer

Defines the time after which the device is turned to last known state. Values (size is 1-byte dec): • Default value 0 • 0 – disabled • 30 – 32535 = 30 – 32535 seconds after which the device turns on

11

2

30

Parameter no. 11. – auto off timer

Values (size is 2-byte dec): Defines the time after which the device is turned to last known state. • Default value 0 • 0 – disabled • 30 – 32535 = 30 – 32535 seconds after which the device turns off

12

2

30

Parameter no. 12. – auto on timer relay

Defines the time after which the device's relay is turned to last known state. Values (size is 2-byte dec): • Default value 0 • 0 – disabled • 30 – 32535 = 30 – 32535 seconds after which the device turns on

13

2

30

Parameter no. 13. – auto off timer relay

Defines the time after which the device's relay is turned to last known state. Values (size is 2-byte dec): • Default value 0 • 0 – disabled • 30 – 32535 = 30 – 32535 seconds after which the device turns off

3

1

1

Parameter no 3. – turning off alarming

Values (size is 1-byte dec): • Default value 1 • 0 – only by z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, switch color set, switch color start/stop level change, notification report idle) • 1 – capacitive input (up, down, left, right) or z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, , switch color set, switch color start/stop level change, notification report idle)

30

1

1

Parameter no. 30. – restore state on power failure

Values (size is 1-byte dec): • Default value 1 • 1 – enabled (the device will restore state on power failure) • 0 – disabled (the device will not restore state on power failure and will remain off)

31

1

1

Parameter no. 31. – restore relay state on power failure

Values (size is 1-byte dec): • Default value 1 • 1 – enabled (the device will restore state on power failure) • 0 – disabled (the device will not restore state on power failure and will remain off)

40

2

10

Parameter no. 40 – Watt Power Consumption Reporting Threshold for Load

Choose by how much power consumption needs to increase or decrease to be reported. Values correspond to percentages so if 10 is set (by default), the device will report any power consumption changes of 10 % or more compared to the last reading. Values (size is 2-byte dec): • Default value 10 • 0 - Power consumption reporting disabled • 1 - 100 = 1 % - 100 % Power consumption reporting enabled. New value is reported only when Wattage in real time changes by more than the percentage value set in this parameter compared to the previous Wattage reading, starting at 1 % (the lowest value possible). NOTE: Power consumption needs to increase or decrease by at least 1 Watt to be reported, REGARDLESS of percentage set in this parameter.

42

2

0

Parameter no. 42 – Watt Power Consumption Reporting Time Threshold for Load

Set value refers to the time interval with which power consumption in Watts is reported (0 – 32535 seconds). If 300 is entered (by default), energy consumption reports will be sent to the gateway (hub) every 300 seconds (or 5 minutes). Values (size is 2-byte dec): • Default value 0 • 0 - Power consumption reporting disabled • 30 - 32535 = 30 - 32535 seconds. Power consumption reporting enabled. Report is sent according to time interval (value) set here.

60

1

0

Parameter no. 60 – Lock touch for relay only

This parameter enables ONLY the touch functionality for closing/opening the relay meant for switching ON/OFF the connected light or any other connected load. See chapter 5.4 for additional information. Values (size is 1-byte dec): • Default value 0 • 0 – disabled • 1 – enabled (the user can switch ON/OFF the connected light or any other connected load by touching ANY button. Other functionalities (lighting mode, scenes, dimming and full white, inclusion/exclusion and reset) are unavailable until function disabled).

70

2

1

Parameter no. 70 - Overload safety switch

The function allows for turning off the controlled device in case of exceeding the defined power for more than 5 sec. Controlled device can be turned back on by capacitive antenna/s or sending a control frame. Values (size is 2-byte dec): • Default value 2300 • 0 = function not active • 1 – 2300 = 1 W – 2300 W ⓘ NOTE: This functionality is not an overload safety protection, please check chapter “Functionalities” for more details. In case of overload the following message will be send towards the controller: COMMAND_CLASS_NOTIFICATION_V5 The Alarm V1 type field set to 0x00 Notification Type 0x08 and 0x08 (Overload detected)

Association Group Information V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V4

COMMAND_CLASS_METER_V4

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Switch Color V3

COMMAND_CLASS_SWITCH_COLOR_V3

Switch Multilevel V4

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Classic Inclusion

1. Enable add/remove mode on your Z-Wave gateway (hub).

2. Connect the device to the power supply.

3. Make sure the device is within direct range of your Z-Wave gateway (hub).

4. Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press, and hold button 3 – right, between 4 and 6 seconds. After 6 seconds, the device starts flashing green (1 second ON, 0.5 second OFF). Once the device receives node ID (after 10 seconds), it stops flashing and turns full green. The procedure is always available.

Note: In case of S2 Security inclusion a dialog will appear prompting you to enter the corresponding PIN number (5 underlined digits) that are written on the module label and the label inserted in the packaging (check the example picture). IMPORTANT: The PIN code must not be lost.

Classic Exclusion

1. Connect the device to the power supply.

2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion.

3. Enable exclusion mode on your Z-Wave gateway (hub).

4. Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press, and hold button 3 – right for 5 seconds. After 5 seconds, the device starts flashing red 1 second ON, 0.5 second OFF.

Once the device loses node ID (after 10 seconds), it stops flashing and turns full red. The procedure is always available.

NOTE: LEARN MODE state allows the device to receive network information from the controller.

Factory Reset Procedure

1. Connect the device to the power supply

2. Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press and hold button 5 – left for 10 seconds. After 10 seconds, the device starts flashing blue 1 second on, 0.5 second off.

After 10 seconds the device stops flashing and turns full blue. The procedure is available always. By resetting the device, all custom parameters previously set on the device will return to their default values, and a node ID will be deleted. Use this reset procedure only when the gateway (hub) is missing or otherwise inoperable.

NOTE: See extended manual for custom settings and parameters available for this device.

Where to find S2 DSK on product

How to locate the DSK label on the product:

When adding the Luxy Smart Switch to a Z-Wave network with a controller

supporting Security 2 (S2), the PIN code of the Z-Wave Device Specific Key (DSK) is required.

The unique DSK code is printed on the product label and a copy is inserted in the packaging,

which must not be lost. Do not remove the DSK from the product. As a backup measure, use

the label in the packaging. The first five digits of the key are highlighted or underlined to help the

user identify the PIN code portion of the DSK text. The DSK is additionally represented with a QR Code.



How to access the DSK via UI:

SMARTSTART INCLUSION

1. Scan QR code on device label and add S2 DSK to Provisioning List in gateway (hub).

2. Connect the device to the power supply.

3. Make sure the device is within direct range of your Z-Wave gateway (hub.

4. Inclusion will be initiated automatically within few seconds of connection to the power supply and the device will automatically enrol in your network (when the device is excluded and connected to the power supply it automatically enters the LEARN MODE state).



MANUAL INCLUSION

1. Enable add/remove mode on your Z-Wave gateway (hub).

2. Connect the device to the power supply.

3. Make sure the device is within direct range of your Z-Wave gateway (hub).

4. Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press, and hold button 3 – right, between 4 and 6 seconds. After 6 seconds, the device starts flashing green (1 second ON, 0.5 second OFF). Once the device receives node ID (after 10 seconds), it stops flashing and turns full green. The procedure is always available.

Note: In case of S2 Security inclusion a dialog will appear prompting you to enter the corresponding PIN number (5 underlined digits) that are written on the module label and the label inserted in the packaging (check the example picture). IMPORTANT: The PIN code must not be lost.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED