Qubino Mini Dimmer - Micromódulo regulador Z-Wave +

Características tecnicas

Tecnologia	Z-Wave Plus
Recurso	Dimmer

Mais Informação

Mini Dimmer Qubino

O Qubino Mini Dimmer é 25% menor que outros dispositivos sem fio similares no mercado. Graças ao seu tamanho pequeno, permite uma instalação rápida e fácil. O sinal sem fio funciona com o protocolo Z-Wave.

Funciona sem fio neutro

O mini-regulador não requer um cabo neutro (N). Funciona em uma configuração de 2 fios.

Instalação do Mini Dimmer Qubino com 2 fios ( sem ponto morto)

Instalação do redutor sem neutro

Instalação Mini Qubino Dimmer 3 fios (neutro)

Mini Dimmer Qubino com instalação neutra

Lâmpadas de 1W

Conecte e controle remotamente lâmpadas economizadoras de energia. Uma carga mínima não é necessária.

Instalação rápida e fácil

Devido ao seu tamanho pequeno, é adequado mesmo para as caixas elétricas menores e mais superficiais e com transbordamento e transbordamentos de cabos.

Instalação do dimmer Qubino Mini

Varie todos os tipos de lâmpadas de intensidade variável

O Qubino Mini Dimmer será calibrado para funcionar com seu tipo específico de lâmpada - de LEDs, fluorescente, halogênio a incandescente. Independentemente do tipo de lâmpada que você usa, o Mini Dimmer oferece uma faixa máxima de regulação.

Lâmpadas incandescentes de até 200W

Lâmpadas halógenas de até 200W

Lâmpadas LED de até 150W

Tiras de led de até 150W

Lâmpadas fluorescentes

É adequado para todos os tipos de caixas embutidas em todo o mundo

Reduza o tempo de montagem e os custos de instalação. Instale-o rápida e facilmente atrás de um comutador convencional.

Sinalização LED

Reconheça facilmente se o Mini Dimmer está incluído ou excluído da rede, seja informado em caso de sobrecarga ou superaquecimento, bem como quando a calibração estiver em andamento.

FUNÇÕES:

O Qubino Mini Dimmer é o menor dimmer sem fio do mundo.
Pode ser instalado em um sistema de 2 fios, sem a necessidade de um fio neutro.
Obviamente, também pode ser instalado em um sistema de 3 fios - com fio neutro
Devido ao seu tamanho pequeno, é adequado até para os armários elétricos menores, mais superficiais e mais confusos.
É adequado para todos os tipos de caixas embutidas em todo o mundo.
Você pode conectar e controlar remotamente as lâmpadas de 1W, sem exigir uma carga mínima.
Ele pode regular todos os tipos de lâmpadas de intensidade variável - incandescentes, halógenas, LED, faixas de luz LED, fluorescentes
Possui sinalização LED para reconhecer facilmente se o Mini Dimmer está incluído ou excluído da rede, em caso de sobrecarga ou superaquecimento e quando a calibração está em andamento.
Consumo de energia extremamente baixo: menos de 0,4 W

AS ESPECIFICAÇÕES TÉCNICAS

Fonte de alimentação: 110 - 240 VAC 50Hz
Corrente nominal de carga de saída: 0.85A
Potência de saída do circuito de saída (carga resistiva): 200W
Precisão da medição do consumo (2 fios): ± 10%.
Precisão da medição do consumo (3 fios): ± 2%.
Temperatura de operação: -10 a +40 ° C
Distância: até 30 m no interior
Dimensões (largura x altura x profundidade): 38 mm x 33,5 mm x 15,5 mm
Peso: 28 g
Consumo de energia: 0,4 W
Para instalação em caixas: Ø e 60 mm ou 2M
Comutação: MOSFET (corte de fase / borda de vazamento)
Repetidor Z-Wave: Sim

Informação alargada da Z-Wave (Inglês)

Nome: Mini Dimmer

Fabricante:QUBINO

Identificador:ZMNHHD1

Número de Certificação Z-Wave :ZC10-21077044

Plataforma de Hardware :ZM5101

FLiRS:Não

Tipo de Role :Always On Slave

Descrição breve :The Qubino Mini Dimmer is the world most compact dimmer. MOSFET-switching light device that also supports control of low-voltage halogen lamps with electronic transformers, dimmable compact fluorescent lights, and dimmable LED bulbs. It can work with or without the neutral line (3 or 2-Wired system).

Descrição :Mini Dimmer is a MOSFET-switching light device that also supports control of low-voltage halogen lamps with electronic transformers, dimmable compact fluorescent lights, and dimmable LED bulbs. It measures power consumption of the connected device. It supports push-button/momentary switches (default) and toggle switches. It can work with or without the neutral line. Qubino Mini Dimmer allows the easiest and quickest installation. It is designed to be mounted inside a “flush mounting box”, hidden behind a traditional wall switch. It acts as repeater in order to improve range and stability of Z-Wave™ network.

Descarregue o manual a partir de aqui.

Grupo

Nodos máximos

Descrição

1

Lifeline.Supports the following command classes: • Device Reset Locally: triggered upon request • Meter Report: triggered according to Configuration parameters 40 and 42 • Notification Report: triggered on overload/over heating • Switch Multilevel Report: triggered upon request or according to Configuration parameters 11 and 12. • Switch Binary Report: triggered upon request or according to Configuration parameters 11 and 12.

2

16

Supports the following command classes: • Basic set: triggered at the change of the output and reflecting its state

3

16

Supports the following command classes: • Start/Stop Level Change: triggered upon holding and releasing the switch connected to terminal I

4

16

Supports the following command classes: • Switch Multilevel Set: triggered at change of output and reflecting its state

Número

Tamanho (Bytes)

Valor por defeito

Nome

Descrição

1

0

In-wall Switch Type for Load to control I1

With this parameter, you can select between push-button (momentary) and on/off toggle switch types.

11

2

0

Turn Load 1 Off Automatically with Timer

If Load is ON, you can schedule it to turn OFF automatically after a period of time defined in this parameter. The timer is reset to zero each time the device receives an ON or OFF command, either remotely (from the gateway (hub) or associated device) or locally from the switch.

12

2

0

Turn Load 1 On Automatically with Timer

If Load is OFF, you can schedule it to turn ON automatically after a period of time defined in this parameter. The timer is reset to zero each time the device receives an OFF or ON command, either remotely (from the gateway (hub) or associated device) or locally from the switch.

21

1

0

Enable/Disable the Double click function

If the Double click function is enabled, a fast double click on the push-button will set the dimming level to the maximum dimming value.

30

1

0

Restore on/off status for load after power failure

This parameter determines if on/off status is saved and restored for the load after power failure.

40

1

10

Watt Power Consumption Reporting Threshold for Load

Choose by how much the power consumption needs to increase or decrease to be reported. Values correspond to percentages so if 10 is set (by default), the device will report any power consumption changes of 10% or more compared to the last reading. ⓘ NOTE: The power consumption needs to increase or decrease by at least 2 Watts to be reported, regardless of percentage set in this parameter.

42

2

0

Watt Power Consumption Reporting Time Threshold for Load

Set value refers to the time interval with which power consumption in Watts is reported (0 – 32767 seconds). If 300 is entered, energy consumption reports will be sent to the gateway (hub) every 300 seconds (or 5 minutes) if there was a change compared from the last report. ⓘNOTE: Values from 1 to 29 are ignored by device due to standard recommendation. ⓘNOTE: The report will be send only if there was a change compared to the last report.

6

1

0

Load type

With this parameter, you select the load type, dimmable or non dimmable. Device operating in dimmable mode on non dimmable load can lead to device or load malfunction. For non dimmable loads par. 6 must be set to 1. ⓘ NOTE: When par.6 set to 1 (non dimmable load) values of listed parameters will be ingnored (par.60 min. dimming value, par.61 max. dimming value, par.65 Dimm. Time when key presed par.66 dimm. Time when key hold, par.21 Double click function ⓘ NOTE: If the bulb is dimmable or non dimmable (generally valid for LED) is shown on the bulb itself or on packaging. ⓘ NOTE: Parameter 6 is replacing parameter 5. Present in previous version.

60

1

15

Minimum dimming value

The value set in this parameter determines the minimum dimming value (the lowest value which can be set on the device, when, for example, dimming lights with wall switch or slider in the GUI (Gateway - hub)) (Data type 1 byte dec) • default value 15 = 15% (minimum dimming value) • 0- 98 = 0% - 98%, step is 1%. Minimum dimming value is set by entering a value. ⓘ NOTE: The minimum level may not be higher than the maximum level!

61

1

99

Maximum dimming value

The value set in this parameter determines the maximum dimming value (the highest value which can be set on the device, when, for example, dimming lights with wall switch or slider in the GUI (Gateway - hub)) ⓘ NOTE: The maximum level may not be lower than the minimum level!

65

1

Dimming time when key pressed (soft on/off)

Choose the time during which the device will move between the min. and max. dimming values by a short press of the push-button I1.

66

2

3

Dimming time when key hold

Choose the time during which the Dimmer will move between the min. and max. dimming values during a continuous press of the push-button I1, by an associated device or through the UI controls (BasicSet, SwitchMultilevelSet).

67

1

0

Ignore start level

Choose whether the device should use (or disregard) the start dimming level value. If the device is configured to use the start level, it should start the dimming process from the currently set dimming level. This parameter is used with association group 3. NOTE: Parameter is valid only in Dimmer mode. In Switch mode the parameter has no effect.

68

1

0

Dimming duration

Choose the time during which the device will transition from the current value to the new target value. This parameter applies to the association group 3. NOTE: Parameter is valid only in Dimmer mode. In Switch mode the parameter has no effect.

70

2

200

Overload safety switch

The function allows for turning off the controlled device in case of exceeding the defined power for more than 5s. Controlled device can be turned back on by input I1 or sending a control frame. ⓘ NOTE: This functionality is not an overload safety protection, please check the technical specifications chapter for more details. In case of overload the following message will be send towards the controller: • COMMAND_CLASS_NOTIFICATION_V5 • The Alarm V1 type field set to 0x00 • Notification Type 0x08 and 0x08 (Overload detected)

71

1

0

Calibration trigger

Choose when will be the calibration procedure triggered.

72

1

2

Calibration status (read only)

With this parameter you can check the calibration status.

73

1

0

Alarm/Notification events

This parameter defines the module behaviour in case it receives any Alarm/Notification events. NOTE: When value 3 is selected the default time interval of the blinking is 10 minutes. It can be stopped with a button press or sending a control frame. To adjust the time interval please refer to parameter 74 – Alarm/Notification time interval.

74

1

10

Alarm/Notification time interval (dependant on parameter 73)

This parameter defines the time interval of the blinking state, once the module receives an alarm/notification event. Minimum step increase is 1 minute. NOTE: This parameter does not have any effect if parameter 73 is not set to value 3.

Basic

COMMAND_CLASS_BASIC

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Association Group Information V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V4

COMMAND_CLASS_METER_V4

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset Procedure

12.5. Device factory reset

1. Connect the device to the power supply.

2. Within the first minute (60 seconds) the device is connected to the power supply, toggle the switch connected to the terminal I 5 times within 3 seconds. The device has to get On/Off signal 5 times, meaning 5 times push of the momentary switch or with toggle switch 5 times On and 5 times Off.

OR

Press and hold the S (Service) button for at least 6 seconds if connected to power supply. For your safety use only 24-30 Vdc power supply when accessing to S (Service) button. This procedure put the device in LEARN MODE.

ⓘ NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the node ID will be deleted. Use this reset procedure only when the main gateway (hub) is missing or otherwise inoperable. If an end device is factory reset, it is reverted to the Z-Wave SmartStart inclusion state.

ⓘ NOTE: the reset with switch connected to terminal I is possible only in the first minute after the device is connected to the power.

ⓘ NOTE: after the reset is successfully done the autocalibration will trigger and the green LED will start blinking.

Classic Inclusion

AUTOMATICALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (SMARTSTART INCLUSION)

1. Scan QR code on device label and add S2 DSK to Provisioning List in gateway (hub)

2. Connect the device to the power supply

3. Inclusion will be initiated automatically within few seconds of connection to the power supply and the device will automatically enrol in your network (when the device is excluded and connected to the power supply it automatically enters the LEARN MODE state).

NOTE: LEARN MODE state allows the device to receive network information from the controller.

ⓘ SmartStart inclusion is a part of S2 security level, so if you want to use SmartStart, you need to include it as S2 Authenticated.

Classic Exclusion

REMOVAL FROM A ZWAVE NETWORK (Z-WAVE EXCLUSION)

1. Connect the device to the power supply.

2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion.

3. Enable add/remove mode on your Z-Wave gateway (hub).

4. Toggle the switch connected to the terminal I 3 times within 3 seconds (this procedure put the device in LEARN MODE). The device has to get On/Off signal 3 times, meaning 3 times push of the momentary switch or with toggle switch 3 times On and 3 times Off.

OR

Press and hold the S (Service) button between 2 and 6 seconds if connected power supply. For your safety use only 24-30 Vdc power supply when accessing to S (Service) button. This procedure put the device in LEARN MODE.

5. Exclusion with the switch connected to terminal I is not limited by time.

6. The device will be removed from your network, but any custom configuration parameters will not be erased.

ⓘ NOTE: LEARN MODE state allows the device to receive network information from the controller.

Where to find S2 DSK on product

IMPORTANT: When adding the Mini Dimmer to a Z-Wave network with a controller supporting Security 2 (S2), the PIN code of the Z-Wave Device Specific Key (DSK) is required. The unique DSK code is printed on the product label and a copy is inserted in the packaging, which must not be lost. Do not remove the DSK from the product. As a backup measure, use the label in the packaging.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Switch Load Capacity Volt-Ampere

The amount of switch load energy the product is rated for in VA (Volt-Amperes)

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.

Outdoor Use

Product is suitable for use outdoors.

Switch Load Capacity Watts

The amount of switch load energy the product is rated for in Watts