-> ->->Fibaro - Chave Dupla 2 - Micromódulo Relé Duplo Ligado / Desligado Z-Wave + com Medição de Consumo

Produtos visualizados





Confianza Online
domoticalia.es/es/ Reviews with ekomi.es
Reduced price! Fibaro "Doble Switch 2" - Micromodulo relé interruptor doble On / Off Z-Wave+ con medición de consumo View larger
Previous Next

Fibaro - Chave Dupla 2 - Micromódulo Relé Duplo Ligado / Desligado Z-Wave + com Medição de Consumo

FGS-223

Novo

O relé / chave do micromódulo Fibaro FGS-223 "Double Switch 2" permitirá que você controle duas luzes ou dois dispositivos remotos enquanto mantém a chave convencional existente.

Mais detalhes

Em estoque

63,89 €

-20%

79,86 €

Características tecnicas

Tecnologia Domótica Z-Wave Plus
Recurso Medição de Consumo

Mais Informação

O novo micro-módulo de interruptor / relé duplo da Fibaro, Fibaro FGS-223 "Chave dupla 2" disponível como uma chave Z-Wave dupla, foi projetado para ativar e desativar dispositivos elétricos ou cargas. Graças ao seu pequeno tamanho, ele pode ser montado em caixas de conexão ou caixas de dispositivos em ambientes internos. O módulo é controlado pela rede Z-Wave ou por um simples switch. Tem a função de medir a potência e o consumo de energia de uso que permite controlar e reduzir a sua fatura de luz. Conecte seu Fibaro FGS-223 "Double Switch 2" no sistema junto com outros dispositivos para desfrutar das possibilidades quase infinitas!

Por se tratar de 1 relé duplo, possui 2 saídas:

  • 6,5 A (1.560 W a 240 V) máx. por saída com carga resistiva.
  • 10A (2.400 W a 240 V) máx. por TOTAL de saída com carga resistiva.

Possui um mecanismo de gatilho de cena embutido

aulas de comunicação e notificação de segurança
menu de configuração com um diodo
Z-Wave de última geração com chip da série 500
Compatível com Z-Wave Plus

Executa funções de repetidor Z-Wave
Mede a energia e potência dos dispositivos conectados
Suporta modo de segurança (Z-Wave Security Network) com criptografia AES-128
Um sistema de controle complexo para cada canal
Um sistema de ativação de cena complexo para cada canal (gerenciamento de cena)
1 a 3 pressões e mantendo a tecla pressionada podem ser atribuídos a quatro ações diferentes
medição de potência muito precisa +/- 1% de potência acima de 5W
Notificações inteligentes
Conexões aprimoradas
menu de configuração simples
Tem uma testemunha de teste de cobertura da rede Z-Wave
Atualizações de software*
compatibilidade com certificação confirmada por FCC, DEKRA, Z-Wave

Verificação de cobertura Z-Wave

Atenção:

Observe que este módulo requer NEUTRO para operar. A saída não é livre de potencial, o que torna impossível controlar um contato seco ou carregar outra tensão de alimentação de entrada.

REPETIMOS: ele não pode ser usado em um esquema de conexão do tipo "contato seco", como seu predecessor, o Fibaro FGS-222, poderia.

Diagrama de fiação do relé Fibaro FGS-223

Imagem de fiação com 1 e 2 circuitos

Imagem de fiação com 1 e 2 circuitos

Diagrama de conexão para controlar 1 zona de iluminação com "chaves comutadas":

Esquema de conexão comutada Fibaro FGS-223

Resumo:

2 saídas:

  • 6,5 A (1560 W a 240 V) máx. por saída com carga resistiva.
  • 10 A (2400 W a 240 V) máx. por TOTAL de saída com carga resistiva.


medição precisa do consumo (+/- 1% de 5W).
Série Z-Wave + 500 (melhor comunicação remota).
comunicações seguras com criptografia AES-128.
Capacidade de acionar cenas de automação residencial * através das entradas S1 e S2 (4 cenas possíveis por botão).
Função de repetidor para estender a rede Z-Wave.
Configuração com função de menu interativo e testador de rede Z-Wave com LED

Rele fibaro tamanho

Z-Wave Plus - Fibaro ZW5

Informação alargada da Z-Wave (Inglês)

Nome: FIBARO Double Switch 2
Fabricante:FIBARO
Identificador:FGS-223
Número de Certificação Z-Wave :ZC10-18015920
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :FIBARO Double Switch 2 is designed to turn two electrical devices on and off and to measure their power and energy consumption.
Descrição :The remotely operated FIBARO Double Switch 2 is designed to turn two electrical devices on and off and to measure their power and energy consumption. The compact size of the device makes it the world's smallest of its type and allows for the product to be installed in wall switch boxes or housings. FIBARO Double Switch 2 can be controlled either via Z-Wave network or with a wall switch through a direct connection.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
“Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2
5
“On/Off (S1)” is assigned to switch connected to the S1 terminal (uses Basic command class).
3
5
“Dimmer (S1)” is assigned to switch connected to the S1 terminal (uses Switch Multilevel command class).
4
5
“On/Off (S2)” is assigned to switch connected to the S2 terminal (uses Basic command class).
5
5
“Dimmer (S2)” is assigned to switch connected to the S2 terminal (uses Switch Multilevel command class).
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
10
1
0
First channel - operating mode
This parameter allows to choose operating for the 1st channel controlled by the S1 switch. 0 - standard operation 1 - delay ON function 2 - delay OFF function 3 - auto ON function 4 - auto OFF function 5 - flash function
11
1
0
First channel - reaction to switch for delay/auto ON/OFF modes
This parameter determines how the device in timed mode reacts to pushing the switch connected to the S1 terminal. 0 - cancel mode and set target state 1 - no reaction to switch - mode runs until it ends 2 - reset timer - start counting from the beginning
12
2
50
First channel - time parameter for delay/auto ON/OFF modes
This parameter allows to set time parameter used in timed modes. 0 (0.1s), 1-32000 (1-32000s, 1s step) - time parameter
13
2
5
First channel - pulse time for flashing mode
This parameter allows to set pulse time used in flashing mode. 1-32000 (0.1-3200.0s, 0.1s step) - time parameter
15
1
0
Second channel - operating mode
This parameter allows to choose operating for the 1st channel controlled by the S2 switch. 0 - standard operation 1 - delay ON function 2 - delay OFF function 3 - auto ON function 4 - auto OFF function 5 - flash function
16
1
0
Second channel - reaction to switch for delay/auto ON/OFF modes
This parameter determines how the device in timed mode reacts to pushing the switch connected to the S2 terminal. 0 - cancel mode and set target state 1 - no reaction to switch - mode runs until it ends 2 - reset timer - start counting from the beginning
17
2
50
Second channel - time parameter for delay/auto ON/OFF modes
This parameter allows to set time parameter used in timed modes. 0 (0.1s), 1-32000 (1-32000s, 1s step) - time parameter
18
2
5
Second channel - pulse time for flashing mode
This parameter allows to set pulse time used in flashing mode. 1-32000 (0.1-3200.0s, 0.1s step) - time parameter
20
1
2
Switch type
This parameter as what type the device should treat the switch connectedto the S1 and S2 terminals. 0 - momentary switch 1 - toggle switch (contact closed - ON, contact opened - OFF) 2 - toggle switch (device changes status when switch changes status)
21
1
0
Flashing mode - reports
This parameter allows to define if the device sends reports during the flashing mode. 0 - the device does not send reports 1 - the device sends reports
27
1
15
Associations in Z-Wave network security mode
This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. This parameter does not apply to 1st „Lifeline” group. 1 - 2nd group sent as secure 2 - 3rd group sent as secure 4 - 4th group sent as secure 8 - 5th group sent as secure NOTE Parameter 27 values may be combined, e.g. 1+2=3 means that 2nd & 3rd groups are sent as secure.
28
1
0
S1 switch - scenes sent
This parameter determines which actions result in sending scene assigned to them. 1 - Key pressed 1 time 2 - Key pressed 2 time 4 - Key pressed 3 time 8 - Key Hold Down and Key Released NOTE Parameter 28 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent.
29
1
0
S2 switch - scenes sent
This parameter determines which actions result in sending scene assigned to them. 1 - Key pressed 1 time 2 - Key pressed 2 time 4 - Key pressed 3 time 8 - Key Hold Down and Key Released NOTE Parameter 29 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent.
30
1
0
S1 switch - associations sent to 2nd and 3rd association groups
This parameter determines which actions result in sending commands to devices associated in 2nd and 3rd association group. All actions are active by default. 1 - ignore turning ON with 1 click of the switch 2 - ignore turning OFF with 1 click of the switch 4 - ignore holding and releasing the switch* 8 - ignore double click of the switch** NOTE Parameter 30 values may be combined, e.g. 1+2=3 means that associations for turningON and OFF are not sent.
32
2
0
S1 switch - Switch OFF value sent to 2nd and 3rd association groups
This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group. 0-255 - sent value 0 - turning off associated devices 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on NOTE Setting parameters 31-33, 36-38 to appropriate value should result in: 0 - turning off associated devices 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
33
2
99
S1 switch - Double Click value sent to 2nd and 3rd association groups
This parameter defines value sent with Double Click command to devices associated in 2nd and 3rd association group. 0-255 - sent value
35
1
0
S2 switch - associations sent to 2nd and 3rd association groups
This parameter determines which actions result in sending commands to devices associated in 2nd and 3rd association group. All actions are active by default. 1 - ignore turning on with 1 click of the switch 2 - ignore turning off with 1 click of the switch 4 - ignore holding and releasing the switch* 8 - ignore double click of the switch** NOTE Parameter 35 values may be combined, e.g. 1+2=3 means that associations for turning ON and OFF are not sent. NOTE *Hold and release is inactive when parameter 20 is set to 1 or 2. **Double click is inactive when parameter 20 is set to 1.
36
2
255
S2 switch - Switch ON value sent to 2nd and 3rd association groups
This parameter defines value sent with Switch ON command to devices associated in 2nd and 3rd association group. 0-255 - sent value 0 - turning off associated devices 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
37
2
0
S2 switch - Switch OFF value sent to 2nd and 3rd association groups
This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group. 0-255 - sent value 0 - turning off associated devices 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
38
2
99
S2 switch - Double Click value sent to 2nd and 3rd association groups
This parameter defines value sent with Double Click command to devices associated in 2nd and 3rd association group. 0-255 - sent value 0 - turning off associated devices 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
40
1
3
Reaction to General Alarm
This parameter determines how the device will react to General Alarm frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame
41
1
2
Reaction to Flood Alarm
This parameter determines how the device will react to Flood Alarm frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame
42
1
3
Reaction to CO/CO2/Smoke Alarm
This parameter determines how the device will react to CO, CO2 or Smoke frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame
43
1
1
Reaction to Heat Alarm
This parameter determines how the device will react to Heat Alarm frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame
44
2
600
Flashing alarm duration
This parameter allows to set duration of flashing alarm mode. 1-32000 (1-32000s, 1s step) - duration
50
1
20
First channel - power reports
This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. 0 - reports are disabled 1-100 (1-100%) - change in power
51
1
10
First channel - minimal time between power reports
This parameter determines minimum time that has to elapse before sending new power report to the main controller. 0 - periodic reports are disabled 1-120 (1-120s) - report interval
53
2
100
First channel - energy reports
This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. 0 - reports are disabled 1-32000 (1-32000Wh) - change in energy
54
1
20
Second channel - power reports
This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. 0 - reports are disabled 1-100 (1-100%) - change in power
55
1
10
Second channel - minimal time between power reports
This parameter determines minimum time that has to elapse before sending new power report to the main controller. 0 - periodic reports are disabled 1-120 (1-120s) - report interval
57
2
100
Second channel - energy reports
This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. 0 - reports are disabled 1-32000 (1-32000Wh) - change in energy
58
2
3600
Periodic power reports
This parameter determines in what time intervals the periodic power reports are sent to the main controller. 0 - periodic reports are disabled 1-32000 (1-32000s) - report interval
59
2
3600
Periodic energy reports
This parameter determines in what time intervals the periodic energy reports are sent to the main controller. 0 - periodic reports are disabled 1-32000 (1-32000s) - report interval
60
1
0
Measuring energy consumed by the device itself
This parameter determines whether energy metering should include the amount of energy consumed by the device itself. Results are being added to energy reports for first endpoint. 0 - function inactive 1 - function activate
9
1
1
Restore state after power failure
This parameter determines if the device will return to state prior to the power failure after power is restored. 0 - the device does not save the state prior to the power failure and returns to „off” position 1 - the device restores its state prior to the power failure
Basic
COMMAND_CLASS_BASIC
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Central Scene V2
COMMAND_CLASS_CENTRAL_SCENE_V2
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V3
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Powerlevel
COMMAND_CLASS_POWERLEVEL
Protection V2
COMMAND_CLASS_PROTECTION_V2
Security S0
COMMAND_CLASS_SECURITY
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Additional Special Features
Z-Wave Plus communication protocol

Active power and energy metering functionality

Z-Wave range tester

LED diode

Inclusion
1) Switch off the mains voltage (disable the fuse).

2) Make sure the Switch 2 is within the direct range of your Z-Wave controller.

3) Connect the device in accordance with one of the diagrams included in the manual.

4) After verifying correctness of the connection switch on the mains voltage.

5) Identify the S1 switch or the B-button (located on the device’s housing).

6) Set the main controller in (security/non-security) add mode (see the controller’s manual).

7) Quickly, three times press the S1 switch or the B-button.

8) Wait for the adding process to end.

9) Successful adding will be confirmed by the Z-Wave controller’s message.
Exclusion
1) Make sure the Switch 2 is within the direct range of your Z-Wave controller.

2) Identify the S1 switch or the B-button (located on the device’s housing).

3) Set the main controller in remove mode (see the controller’s manual).

4) Quickly, three times press the S1 switch or the B-button.

5) Wait for the removing process to end.

6) Successful removing will be confirmed by the Z-Wave controller’s message.
Device Wake-Up
The FIBARO Double Switch 2 is powered with the mains voltage so it is always awake.
Factory Reset
Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. In order to reset the device:



1) Switch off the mains voltage (disable the fuse).

2) Remove the Switch 2 from the wall switch box.

3) Switch on the mains voltage.

4) Press and hold the B-button to enter the menu.

5) Wait for the visual LED indicator to glow yellow.

6) Quickly release and click the B-button again.

7) After few seconds the device will be restarted, which is signalled with the red LED indicator colour.



Use reset procedure only if the primary controller is missing or inoperable.

Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts
Color
If the product is only available in one color, pick the color from the list.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Supported Meter Type
Indicate which type of metering is supported by the device.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).

 

Avaliações

Nota 
2021-11-25

Domtizar luces

Buen rele para domotizar luces encendido/apagado. Facil de parametrizar para pulsador con los parametros Z-Wave

Nota 
2019-10-29

Envio rapido

Asesoramiento correcto. Envio rapido y bien.

Faça uma avaliação!

Escrever uma avaliação

Fibaro - Chave Dupla 2 - Micromódulo Relé Duplo Ligado / Desligado Z-Wave + com Medição de Consumo

Fibaro - Chave Dupla 2 - Micromódulo Relé Duplo Ligado / Desligado Z-Wave + com Medição de Consumo

O relé / chave do micromódulo Fibaro FGS-223 "Double Switch 2" permitirá que você controle duas luzes ou dois dispositivos remotos enquanto mantém a chave convencional existente.

30 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram:

Newsletter


Información básica Política de Privacidad

Siga-nos

Utilizamos cookies próprios e de terceiros para melhorar nossos serviços e mostrar publicidade relacionada às suas preferências, analisando seus hábitos de navegação. Se você continuar navegando, consideramos que você aceita seu uso. Você pode obter mais informações ou saber como alterar a configuração em nossa Política de Cookies close

A minha conta