Carrinho
0
Produto
Produtos
(vazio)
Sem produtos
Envio grátis!
Envio
0,00 €
IVA
0,00 €
Total
Preços com IVA
Produto adicionado com sucesso ao seu carrinho de compras
Quantidade
Total
Existem 0 produtos no seu carrinho de compras. Existe um produto no seu carrinho de compras.
Total produtos
(com IVA)
Total portes (com IVA)
Envio grátis!
IVA
0,00 €
Total
(com IVA)
Aeotec
Aeotec MultiSensor 7 - 6 em 1 Z-Wave Detector Multifuncional Série 700
Aeotec MultiSensor 7 - 6 em 1 Z-Wave Detector Multifuncional Série 700
AEOEZWA024-C
Novo
O Aeotec MultiSensor 7 é um sensor multifuncional para temperatura, umidade, movimento, UV e vibração.
Em estoque
- Retirar este produto da minha lista de favoritos.
- Adicionar este produto à minha lista de favoritos.
Características tecnicas
| Tecnologia Domótica | Z-Wave Serie 700 |
Mais Informação
Aeotec MultiSensor 7
Movimento por segurança. Movimento para a presença. Movimento para a gestão. O sensor de movimento Aeotec MultiSensor 7 é perfeito para mais do que apenas um sistema de segurança inteligente. Com um alcance de 10 metros e um campo ou ângulo de visão de 120°, o MultiSensor 7 captura dados de movimento que podem ser usados para tudo, desde segurança até gerenciamento de aquecimento e economia de energia. Saber se um cômodo está ocupado ou se um corredor está em uso é uma informação muito poderosa: o MultiSensor 7 torna seu sistema de automação residencial mais poderoso e inteligente.
Sensor de temperatura. Aeotec MultiSensor 7
De persianas e janelas motorizadas a ventiladores e termostatos, há muitas maneiras de usar o Z-Wave para manter a temperatura ambiente absolutamente perfeita. O MultiSensor 7 fornece a inteligência para fazer exatamente isso. Dentro de cada sensor há um sensor de temperatura incremental capaz de medir com precisão entre -10~50°C (14 a 122°F) e relatar mudanças de temperatura para um gateway doméstico inteligente.
Sensor de luz. Aeotec MultiSensor 7
A iluminação automatizada é tão inteligente quanto o sistema que a alimenta. Com o sensor de luz digital em tempo real MultiSensor 7, que mede o nível de luz em uma sala, seu sistema de controle doméstico pode manter seu ambiente de forma inteligente. Desde a abertura e fechamento de persianas até a configuração das luzes no nível perfeito, dia ou noite, o MultiSensor 7 é a inteligência por trás da iluminação inteligente.
Sensor de umidade. Aeotec MultiSensor 7
Espaços como banheiros e cozinhas podem ser muito úmidos, enquanto alguns ambientes geralmente não são úmidos o suficiente. O MultiSensor 6 oferece monitoramento incremental de umidade de 0% a 100%, permitindo automação inteligente de ventiladores, janelas motorizadas, desumidificadores e umidificadores. O MultiSensor 7 monitora sua casa em um nível tão infinitesimal que seu sistema de gerenciamento doméstico pode tornar seu ambiente realmente perfeito.
Sensor de vibração. Aeotec MultiSensor 7
Ele mede o ambiente em que se encontra e também mede a si mesmo. O MultiSensor 7 contém um sensor sísmico capaz de detectar e relatar vibrações baseadas em eventos. Essas pequenas alterações podem ser usadas para proteger o MultiSensor 7: você sabe se um intruso o está adulterando ou se o sensor foi movido acidentalmente de seu local de montagem. Também é capaz de registrar atividades sísmicas sutis dentro de sua casa.
Sensor UV. Aeotec MultiSensor 7
Gerenciar perfeitamente um ambiente significa entendê-lo perfeitamente. O MultiSensor 6 mede com precisão a luz ultravioleta, o tipo de luz que causa tudo, desde clarear móveis até danificar os olhos. Medido de acordo com o Índice UV da Organização Mundial da Saúde, o MultiSensor 7 mede o nível UV de uma sala para poder gerenciar um ambiente através de cortinas, persianas e iluminação, e para poder fazer recomendações de saúde e propriedade.
Poder perfeito. Aeotec MultiSensor 7
A duração perfeita da bateria é perfeita para cada instalação. Para todos esses momentos, o MultiSensor 7 pode funcionar com energia da rede elétrica. Basta conectá-lo à eletricidade de sua casa através do cabo USB fornecido e o MultiSensor 7 pode funcionar em modo avançado, fornecendo leituras de temperatura, umidade e luz em tempo real.
Caracteristicas:
MultiSensor Z-Wave com 6 sensores integrados (movimento, temperatura, luz, umidade, vibração e UV).
Construído com a série Z-Wave 700 - maior alcance, mais eficiência e melhor desempenho em comparação com a série da geração anterior
Tecnologia sem fio: Z-Wave Plus V2
Habilitado para SmartStart
Segurança S2
Funciona com cabo USB ou baterias (até 2 anos de duração da bateria)
Transmissão de dados para o centro de controle em tempo real e tecnologia de sensores otimizada em comparação com seu antecessor Aeotec MultiSensor 6
Informação alargada da Z-Wave (Inglês)
Nome: MultiSensor 7
Fabricante:Aeotec
Identificador:ZWA024-C
Número de Certificação Z-Wave :ZC12-20120147
Plataforma de Hardware :ZGM130
FLiRS:Sim
Tipo de Role :Always On Slave
Descrição breve :Z-Wave MultiSensor 7
Descrição :Aeotec MultiSensor 7 is a sensor with ambient light/UV, temperature, humidity, vibration and motion.
Descarregue o manual a partir de aqui.
Grupo
Nodos máximos
Descrição
1
5
Device Reset Locally:
When factory reset.
Notification Report:
See Notification Chapter for more information.
Sensor Binary Report:
See Param5 for more information.
Sensor Multilevel Report:
When sensors above over limit or below under limit.
Battery Report:
See Param101.
Indicator Report:
Issued when the indicator light changed
2
5
Basic Set Command will be sent to the associated device when
motion trigger or untrigger. The basic set value is determined
by Param11, Param12. See Param13 for more information.
3
5
Basic Set:
When the temperature change value is over or under the threshold set by Param16. Scale is determined by Param64.
4
5
Basic Set:
When the temperature change value is under or over the threshold set by Param17. Scale is determined by Param64.
5
5
Basic Set:
When the current humidity is over or under the threshold set by Param14
6
5
Basic Set:
When the current humidity is under or over the threshold set by Param15
7
5
Basic Set:
When the current light/lux is over or under the threshold set by Param18
8
5
Basic Set:
When the current light/lux is under or over the threshold set by Param19.
9
5
Basic Set:
When the current UV is over or under the threshold set by Param20
10
5
Basic Set:
When the current UV is under or over the threshold set by Param21
11
5
Sensor Multilevel Report:
When sensors above over limit or below under limit.
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
1
Beaming Enable/Disable
Used to enable/disable beaming. If set to 1, FLiR commands will be supported. But the device must be re-included into the network to activate it.
0 - disable
1 - enable
10
1
0
Power Status
This value is Readonly. Used to report the power status (USB or Battery powered)
0 - When battery powered, the device will act as RSS.
1 - When USB cable insert, the device will act as LSS.
The device must be re-included in the network to change the role type.
101
1
241
Automatic Report Checklist 1
Checklist 1 for automatic timed report. When the corresponding item is selected, it will be checked when timeout setting by Param111.
1 - Battery
16 - UV
32 - Temperature
64 - Humidity
128 - Lux
102
1
0
Automatic Report Checklist 2
Checklist 2 for automatic timed report. When the corresponding item is selected, it will be checked when timeout setting by Param112.
1 - Battery
16 -
32 - Temperature
64 - Humidity
128 - Lux
103
1
0
Automatic Report Checklist 3
Checklist 3 for automatic timed report. When the corresponding item is selected, it will be checked when timeout setting by Param113.
1 - Battery
16 - UV
32 - Temperature
64 - Humidity
128 - Lux
11
1
0
Motion Group Control(Group2)
Set control of other devices on group2 based on motion trigger.
0 - Send BASIC_SET (0xFF) when motion is triggered to associated device
Send BASIC_SET (0x00) when motion is untriggered to associated device
1 - Send BASIC_SET (0x00) when motion is triggered
Send BASIC_SET (0xFF) when motion is untriggered
2 - Send BASIC_SET (0xFF) when motion is triggered, Nothing when motion untriggered.
3 - Send BASIC_SET (0x00) when motion is triggered, Nothing when motion untriggered.
4 - Send BASIC_SET (0x00) when motion is untriggered, Nothing when motion triggered.
5 - Send BASIC_SET (0xFF) when motion is untriggered, Nothing when motion triggered.
6 - Send BASIC_SET (value is configured by parameter 12) when motion is triggered to associated devices.
Send BASIC_SET (value is configured by parameter 12) when motion is untriggered.
111
2
3600
Automatic Checklist 1 Interval Time
Interval time set in seconds to check the checklist1’s items. Multilevel Sensor Report will be sent when timeout.
112
2
3600
Automatic Checklist 2 Interval Time
Interval time set in seconds to check the checklist2’s items. Multilevel Sensor Report will be sent when timeout.
113
2
3600
Automatic Checklist 3 Interval Time
Interval time set in seconds to check the checklist3’s items. Multilevel Sensor Report will be sent when timeout.
12
2
65280
Motion Group Value Setting
Set Basic Set value for Group2. The MSB will act as the basic set value when motion trigger. The LSB will act as the basic set value when motion untrigger. E.g. value=0x0A00, then BASIC_SET(0x0A) will be sent when motion trigger, BASIC_SET(0x00) will be sent when motion untrigger.
13
2
30000
Motion Group Control Requirement
Set threshold of Light/Lux when devices associated in group2 should be triggered by motion. Associated device only receive BASIC_SET command when light
14
1
60
Over Humidity Group Threshold (Group5)
Set threshold of humidity. If measured humidity >= (this value), send BASIC_SET (0xFF) to associated devices through group5. If measured humidity < (this value) send BASIC_SET (0x00) to associated devices through group5.
15
1
40
Under Humidity Group Threshold (Group6)
Set threshold of humidity. If measure humidity (this value) send BASIC_SET (0x00) to associated devices through group6.
16
2
239
Over Heat Group Threshold (Group3)
Set threshold of temperature. Designed to control Air Conditioners or temperature controllers ON or OFF. If measured
temperature >= (this value, Scale is determined by Param64) send BASIC_SET (0xFF) to associated devices. If measured temperature<(this value) send BASIC_SET (0x00) to associated devices. E.g. Value 239 means 23.9 C. Value 750 means 75.0 F.
17
2
155
Under Heat Group Threshold (Group4)
Set threshold of temperature. Designed to control Air Conditioners or temperature controllers ON or OFF. If measured temperature (this value) send BASIC_SET (0x00) to associated devices. E.g. Value 155 means 15.5 C. Value 600 means 60.0 F.
18
2
2000
Over Light Group Threshold (Group7)
Set threshold of Light/Lux. If measured light/lux >= (this value) send BASIC_SET (0xFF) to associated devices. If measured light/lux < (this value) send BASIC_SET (0x00) to associated devices.
19
2
100
Under Light Group Threshold (Group8)
Set threshold of Light/Lux. If measured light/lux (this value) send BASIC_SET (0x00) to associated devices.
2
2
30
Motion Retrigger Time
Presence re-detection time set in second to allow motion sensor to reset timeout of motion sensor. In this time, the motion sensor can not be triggered again. If this value reach zero, the timeout configuration value set by Param3 will be reset. This setting value must always be less than timeout configuration.
0 - disable
1~3600 - timeout set in seconds
20
1
8
Over UV Group Threshold (Group9)
Set threshold of UV. If measured UV >= (this value) send BASIC_SET (0xFF) to associated devices. If measured UV < (this value) send BASIC_SET (0x00) to associated devices.
201
2
0
Temperature Offset Value
Can add or minus this setting value to calibrate temperature when checked. Scale is defined by Param64. e.g. Value 15 means 1.5C or 1.5F.
202
1
0
Humidity Offset Value
Can add or minus this setting value to calibrate humidity when checked. Unit: %.
203
2
0
Lux Offset Value
Can add or minus this setting value to calibrate Lux when checked.
204
1
0
UV Offset Value
Can add or minus this setting value to calibrate UV when checked.
21
1
1
Under UV Group Threshold (Group10)
Set threshold of UV. If measured UV (this value) send BASIC_SET (0x00 to associated devices.)
3
2
240
Motion Untrigger Time
Timeout configuration set in second for motion sensor to send no trigger status.
39
1
50
Low Battery Threshold
Configure low battery report threshold, sends low battery report via notification and battery report when battery level drops under setting. Unit %.
4
1
11
Motion Sensitivity
Set the sensitivity of motion sensor.
0 - disable
1- minimum sensitivity
11 - maximum sensitivity
40
1
0
Threshold Check Enable/Disable
Enable/Disable threshold reporting, check time can be adjusted by Param45.
0 - disable all threshold reports
1 - enable all threshold reports
41
1
10
Temperature Threshold
Threshold = (Value * 0.1) Scale is determined by Param64. 0 = disable.
42
1
5
Humidity Threshold
Humidity range = 1% to 50%, 0 = disable.
43
2
250
Lux Threshold
0 = disable
44
1
1
UV Threshold
0 = disable
45
2
240
Threshold Check Time
Set threshold check time in seconds if threshold is enable via Param40.
1~65535 - When USB powered
60~65535 - When Battery powered
46
1
1
Low Temperature Report
Eable/Disable alarm report for low temperature(
48
1
0
Sensor Limit Control
This value is bit mask. Used to enable/disable measurement reports for various sensors that is more than the upper limit value or less than the lower limit value.
1 - Temperature upper level
2 - Humidity upper level
4 - Lux upper level
8 - UV upper level
16 - Temperature lower level
32 - Humidity lower level
64 - Lux lower level
128 - UV lower level
49
2
280
Temperature Upper Limit
Set upper limit level for temperature set in scale of 0.1. Scale is determined by Param64. If (Current measurement) > (Upper Limit), then report sensor.
5
1
2
Motion Report Type
Set which command class will be sent when motion sensor is triggered or detriggered.
0 - Sends Notification Report
1 - Sends Sensor Binary Report
2 - Sends Notification and Sensor Binary Report
50
2
0
Temperature Lower Limit
Set lower limit level for temperature set in scale of 0.1. Scale is determined by Param64. If (Current Measurement) < (Lower limit), then report sensor.
51
1
20
Temperature Recover Limit
Temperature recover limit set in scale of 0.1. Scale is determined by Param64. If (Current measurement) = (lower limit + recover limit), then temperature report.
52
1
60
Humidity Upper Limit
Set humidity upper limit level.
53
1
40
Humidity Lower Limit
Set humidity lower limit level
54
1
5
Humidity Recover Limit
Set humidity recover limit level. Refer to Param 51.
55
2
1000
Lux Upper Limit
Set lux upper limit level.
56
2
100
Lux Lower Limit
Set lux lower limit level.
58
1
8
UV Upper Limit
Set UV upper limit level.
59
1
4
UV Lower Limit
Set UV lower limit level.
6
1
255
Vibration Sensor Enable/Disable
Used to enable/disable vibration sensor.
0 - disable vibration
1~254 - timeout set in minutes to reset vibration status
255 - timeout set in minutes to reset vibration status
60
1
1
UV Recover Limit
Set UV recover limit level. Refer to Param 51.
61
1
0
Out-of-limit State
This is read only and bit mask. Out of the limit state of sensors.
Bit Mask:
0 - within limit
1 - out of limit
Value:
1 - Temperature upper level
2 - Humidity upper level
4 - Lux upper level
8 - UV upper level
16 - Temperature lower level
32 - Humidity lower level
64 - Lux lower level
128 - UV lower level
64
1
0
Temperature Scale
Set the scale for temperature when reports.
0 - Celsius
1 - Fahrenheit
67
1
100
Lux Recover Limit
Set lux recover limit level. Refer to Param 51.
7
1
0
Vibration Intensity Reports
Used to enable/disable vibration intensity reports. If set to 1, vibration intensity will be sent to gateway when triggered. If set to 0, do not report.
81
1
1
LED Activity
Allow user to enable/disable LED activity of specific reports sent by sensor. Button press indicator is not affected by this.
0 - disable
1 - enable
82
1
3
Motion Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of motion sensor.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
83
1
0
Temperature Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of temperature sensor.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
84
1
0
Humidity Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of humidity sensor.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
85
1
0
Lux Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of Lux sensor.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
86
1
0
UV Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of UV sensor.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
87
1
2
Vibration Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of vibration sensor.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
88
1
0
Battery Report Indicator
If LED is enabled by Param81, allow user to change the report color of battery.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
89
1
8
Wakeup Report Indicator
If LED is enabled by Param81, allow user to change the report color of wakeup.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
9
1
15
Wakeup CC Timeout
Timeout set in seconds after Wakeup CC is send out before go to sleep. If wakeup no more information received, return to sleep mode immediately.
90
1
0
Communication Indicator
If LED is enabled by Param81, allow user to change indicator color when receiving communication from gateway or other devices.
0 - Disabled
1 - Red
2 - Blue
3 - Green
4 - Pink
5 - Cyan
6 - Purple
7 - Orange
8 - Yellow
9 - White
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Information V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration V4
COMMAND_CLASS_CONFIGURATION_V4
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V5
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
Indicator V3
COMMAND_CLASS_INDICATOR_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Binary V2
COMMAND_CLASS_SENSOR_BINARY_V2
Sensor Multilevel V11
COMMAND_CLASS_SENSOR_MULTILEVEL_V11
Supervision
COMMAND_CLASS_SUPERVISION
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Where to find S2 DSK on product
User guide section in the User manual.
Classic Inclusion
1. Turn your primary controller into inclusion mode.
2. Press once the Action Button on the product.
2. Press once the Action Button on the product.
Classic Exclusion
1. Turn your primary controller into exclusion mode.
2. Press once the Action Button on the product.
2. Press once the Action Button on the product.
Factory Reset Procedure
Press and hold the Action Button on product for 15-20s.
Wake-Up Procedure
Press and hold the Action button on product for 2-5s.
Dynamic Capabilities
The Sensor supports RSS and AOS role type:
1. When battery powered, the device will act as RSS.
2. When USB adpater powered, the device will act as AOS.
Note: The device must be re-included in the network if changing its role type.
1. When battery powered, the device will act as RSS.
2. When USB adpater powered, the device will act as AOS.
Note: The device must be re-included in the network if changing its role type.
Notice of Capability Rediscovery Needed
If the product is in sleep state for a long time and your gateway shows it is in offline state, you can rediscover it via pressing and holding the Action Button for 3 seconds, then the Sensor will send a wake_up notification report to your gateway and let your gateway that it is still online.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Color
If the product is only available in one color, pick the color from the list.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
