Sensor de porta/janela Aeotec 7 PRO Series 700 abertura de porta ou janela

Características tecnicas

Tecnologia Domótica	Z-Wave Serie 700

Mais Informação

Sensor de abertura de porta Z-Wave+ V2 (série 700) Sensor de porta/janela Aeotec 7

O sensor de janela de porta Aeotec 7 Pro é um sensor que detecta se sua janela está aberta, fechada ou inclinada, o que requer um ângulo de inclinação de pelo menos 5°. O sensor é facilmente adaptável. Além disso, o Aeotec Door Window Sensor 7 Pro pode incluir outros sensores ao ser conectado a outros sensores binários, como contatos NTC, microinterruptores ou sensor de inundação.

Graças ao seu design fino, o Aeotec Door Window Sensor 7 Pro pode ser colocado discretamente em qualquer janela. O sensor só tem de ser instalado no caixilho da janela. Além disso, deve haver um ímã fino instalado próximo ao sensor na moldura da janela.

Com o potencial de entrada gratuita, o Aeotec Door Window Sensor 7 Pro também pode incluir outros sensores em seu sistema Z-Wave. Para fazer isso, o sensor binário é conectado à entrada livre de potencial do sensor. Além dos sensores, também podem ser conectados interruptores momentâneos, que controlam cenas em seu gateway.

Se o Aeotec Door Window Sensor 7 Pro falhar uma vez, o núcleo - a placa de circuito - pode ser facilmente substituído sem remover o sensor. Isso permite que você cole o dispositivo na moldura da janela e substitua apenas a placa de circuito.

Caracteristicas:

Construído com a série Z-Wave 700 - maior alcance, mais eficiência e melhor desempenho em comparação com a série da geração anterior
Sensor Z-Wave para portas e janelas
Detecção aberta, fechada ou inclinada graças à tecnologia de sensor patenteada (ângulo de inclinação de pelo menos 5°)
Entrada binária livre de potencial para conectar sensores externos
Tecnologia sem fio: Z-Wave Plus V2
SmartStart
Segurança S2
Troca simples e sem desperdício de placa de circuito
Proteção contra adulteração integrada
Alimentado por bateria (1x ER14250), até 3 anos de duração da bateria

Dimensões (LxAxP)	19 x 71 x 18 mm
Dimensões da embalagem (LxAxP)	73 x 121 x 33 mm
Peso líquido	0,017Kg
Peso bruto	0,062 kg
Bateria	ER14250 (1/2AA)
Z Onda S2
REEE
CE
Classificação de IP	IP20

Informação alargada da Z-Wave (Inglês)

Nome: Door / Window Sensor 7 Pro

Fabricante:Aeotec

Identificador:ZWA012-C

Número de Certificação Z-Wave :ZC12-20060075

Plataforma de Hardware :ZGM130

FLiRS:Não

Tipo de Role :Reporting Sleeping Slave

Descrição breve :A 700 series sensor, which monitors if your window is open, closed or tilted. Can be connected to other sensors via a binary dry input.

Descrição :Aeotec Door/ Window Sensor 7 Pro is built on the 700 series Z-Wave technology. Its a small window position sensor for your smart home, it monitors window and their exact opening position and lets your know when a window is tilted or completely opened. It also supports connecting external binary sensors with a dry contact through the dry binary contact of the Door/ Window sensor. Using the latest technology it supports the highest Z-Wave security level of S2 and SmartStart.

Descarregue o manual a partir de aqui.

Grupo

Nodos máximos

Descrição

1

5

Lifeline to Gateway

2

5

Control devices when a magnet or external dry contacts trips

3

5

Sends out alarm message when a magnet or external dry sensor trips

4

5

Sends alarm messages when tamper is tripped

5

Control devices when tilting sensor trips

Número

Tamanho (Bytes)

Valor por defeito

Nome

Descrição

1

0

Sensor Operation Mode

This parameter defines if the internal magnet sensor or the external terminal input is detected and used to issue alarm notification. There is always one input active only. The other sensor input the deactivated.

10

2

0

Time Delay of "On" command frame

On command is sent after a delay defined in this parameter.

11

2

0

Time Delay of "Off" command frame

Off command is sent after a delay defined in this parameter.

12

2

0

Delay of Tamper Alarm Cancellation

Time a tamper alarm is delayed.

13

1

Reporting Tamper Alarm Cancellation

This parameter defines if the alarm cancellation event is reported.

14

1

0

Central Scene Event Functionality

This parameter enables/disables the central scene function.

15

1

Tilt Sensor Functionality

This parameter enables/disables the tilt function.

16

1

0

Tilt Sensor State

This parameter allows to set in what state is door/window when the tilt is in an OFF state.

17

1

0

5th Association Group triggers

Parameter defines events which result in sending On/Off commands to devices added to the 2nd Association Group. These commands are sent alternately to switch the devices On and Off. Commands represent the values of BASIC SET command frames.

18

1

2

Commands sent to 5th Association Group

Command frames sent to devices added to the 5th association group.

19

1

255

Value of ON command frame sent to 5th Associatio

The value of 0 turns OFF the device, 255 turns it On. In case of associating the Dimmer or Roller Shutter module, values 1-99 allow to set an Associated device to a specified level. 0-99 or 255

2

1

0

Dry Contact Operation Mode

Parameter defines how dry contact will operate with the sensor or switch that is connected to the dry contact terminals. 0 - NO Toggle / Follow state will follow the input of the dry contact terminals where OFF is CLOSED, and ON is OPEN. 1 - NC Toggle / Follow state will follow the input of the dry contact terminals where ON is CLOSED, and OFF is OPEN. 2 - NO save state will allow state of sensor to toggle OPEN/CLOSE based on OFF to ON signal. 3 - NC save state will allow state of sensor to toggle OPEN/CLOSE based on ON toOFF signal.

21

1

50

Tilt sensitivity

You can use this parameter to adjust the tilt sensitivity if the tilt is too low or too high.

255

4

0

Reset Parameter

0 – Nothing happens 0x55555555 – Completely factory reset sensor and send device reset locally notification. All other values – Reset all Parameter settings to their default settings.

3

1

0

Sensor State Polarity

This parameter defines the polarity of the magnet sensor.

4

1

7

Visual LED Indications

This parameter defines when the red LED will indicate events. Disabling all indications may extend battery life.

5

1

0

Range Test after double click

Allows to enable the activation of a Z-Wave range test with double clicking the tamper switch.

6

1

0

2nd Association Group Trigger

This parameter defines the status of the magnet switch that causes sending a BASIC command to all devices of Association Group 2.

7

1

2

Command Sent to Devices of Association Group 2

This parameter defines which commands is sent to 2nd Association Group

8

1

255

BASIC command "On event" value

This is the BASIC command value sent in case of "On" event.

9

1

0

BASIC command "Off event" value

This is the BASIC command value sent in case of "Off" event.

Association Group Information V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Battery

COMMAND_CLASS_BATTERY

Central Scene V3

COMMAND_CLASS_CENTRAL_SCENE_V3

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Binary V2

COMMAND_CLASS_SENSOR_BINARY_V2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Wake Up V2

COMMAND_CLASS_WAKE_UP_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

The DSK for the S2 inclusion can be found inside the sensors packaging.

Classic Inclusion

Inclusion

1. Open the housing.

2. Remove the battery protection.

3. Press the tamper on the side of the appliance three times quickly.

Classic Exclusion

Exclusion

1. Open the housing.

2. Press the tamper on the side of the appliance three times quickly.

Factory Reset Procedure

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED

blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the

GREEN LED blinks once.

Wake-Up Procedure

The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action: Press the tamper once

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Color

If the product is only available in one color, pick the color from the list.

Battery Quantity

Enter the number of batteries of the designated type that the product uses.

Battery Type

Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.